TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 10/2017
1 of 2
PRODUCT INFORMATION
BEHR® Oil-Base Interior/Exterior Satin Enamel is a mildew-resistant paint formula is fast drying, and will help protect both
interior and exterior surfaces from scus, rust and household chemicals.
RECOMMENDED USES:
Ideal for use on properly prepared, interior or exterior surfaces such as:
• Concrete • Concrete Block/CMU • Cement Board Siding • Brick
• Stucco • Plaster • Wood • Plywood
• Ferrous Metals • Non-Ferrous Metals
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 7800 128 oz. / 2 oz.
No. 7830 116 oz. /14 oz.
Resin Type: Alkyd
Gloss: 15-25 @ 60° after 14 day cure
Weight per Gallon: 11.47 lbs.
% Solids by Volume: 53.0 ± 2%
% Solids by Weight: 73.0 ± 2%
VOC: <380 g/L
Flash Point: 104°F
Viscosity: 80-90 KU
Recommended Film Thickness:
Smooth Surfaces:
Wet: 3.2 Dry: 1.7 mils @ 500 Sq. Ft./Gal.
Wet: 2.9 Dry: 1.5 mils @ 550 Sq. Ft./Gal.
Rough Surfaces:
Wet: 4.6 Dry: 2.4 mils @ 350 Sq. Ft./Gal.
Wet: 4.0 Dry: 2.1 mils @ 400 Sq. Ft./Gal.
Coverage: 500-550 Sq. Ft./Gal. for primed, smooth
surfaces, 350-400 Sq. Ft./Gal. for primed, rough surfaces
depending on application method and substrate porosity.
Does not include the loss of material from spraying.
Dry Time to Touch / To Recoat / Full Cure: 2-3 hours /
24 hours / 7 days. Use adequate ventilation during
application and drying process.
APPLICATION:
Brush: China Bristle
Roller:
Smooth Surface: 1/4" - 3/8" nap
Rough Surface: 3/8" - 1/2" nap
Airless Spray: At packaged consistency
Tip: .013"- .017"
Filter: 60 mesh
Thinning: Not recommended
SURFACE PREPARATION:
Proper surface preparation is required.
Allow new stucco, plaster and masonry to cure for 30 days.
Clean
• For interior and exterior surfaces, remove dirt, oil and
grease stains with a product such as BEHR PREMIUM®
Concrete & Masonry Degreaser & Cleaner No. 990.
• Remove mildew stains with a mildew stain
removing product.
• Remove all loose and peeling paint; scu sand glossy
surfaces; caulk; repair imperfections and sand smooth.
• For exterior surfaces, power wash to remove chalk.
• Etch galvanized metal with a chemical etcher. Follow all
label instructions.
Prime
• Use a product such as BEHR PREMIUM PLUS® Exterior
Multi-Surface Primer & Sealer No. 436. Follow all
label instructions.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
Drywall:
• KILZ® Original Primer, Sealer and Stainblocker
Wood:
• BEHR PREMIUM PLUS® Exterior Multi-Surface Primer
& Sealer No. 436
• KILZ COMPLETE® Primer, Sealer and Stainblocker
Tannin/Stain-blocking:
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
• KILZ COMPLETE® Primer, Sealer and Stainblocker
Masonry:
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
Ferrous and Non-Ferrous Metal:
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
CLEAN UP:
Clean all tools and equipment with mineral spirits.
For proper disposal of empty containers and unused
product, contact your household refuse collection service.
Properly dispose of all soiled rags.
COMPLIES WITH THE BELOW AS OF 10/1/2017
AIM YES
OILBASE INTERIOR/EXTERIOR SATIN ENAMEL
NO. 7800