TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any
other nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings
Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 12/2015
1 of 1
GRANITE GRIP™ CONCRETE COATING
NO. 650 & NO. 655
PRODUCT INFORMATION
This interior/exterior decorative oor coating revives concrete surfaces by providing a durable protective nish that lls hairline
cracks up to 1/8" and resists dirt and grease. Its slip-resistant coating is ideal for horizontal surfaces such as walkways, patios,
porches, and pool decks.
RECOMMENDED USES:
Use on properly prepared interior and exterior horizontal surfaces such as:
• Porous Concrete • Masonry • Brick
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 650 128 oz. / 1/16 oz. max
No. 655 128 oz. / 1/16 oz. max
Gloss: < 10 @ 60°
Sheen: < 10 @ 85°
Resin Type: Acrylic
Weight per Gallon: 10.92 lbs
% Solids by Volume: 39.1%
% Solids by Weight: 54.0%
VOC: < 50 g/L
Flash Point: N/A
Viscosity: 118 to 128 KU’s
Recommended Film Thickness (approximate):
Wet: 40 mils, Dry: 16 mils @ 40 Sq. Ft./Gal. (2 Coats)
Wet: 27 mils, Dry: 11 mils @ 60 Sq. Ft./Gal. (2 Coats)
Coverage: 40 to 60 Sq. Ft./Gal. (2 Coats required)
APPLICATION:
Brush: Synthetic
Roller: 1/4" Adhesive Roller
Airless Spray: N/A
Texture Sprayer: Capable of 40 psi
Tip: 4 mm
Filter: N/A
Thinning: DO NOT THIN. Product is formulated for
use at package consistency.
Dry Time: @ 77°F (25°C), 50% RH
Longer dry time required in cooler temperatures and
in higher humidity.
To Touch: 1 hour
To Recoat: 3-4 hours
Apply a rst coat using a 1/4" adhesive roller cover,
nylon/polyester brush or synthetic stain pad.
NOTE: The rst coat will act as the base coat and it will
not completely cover the surface by design. Avoid over
application on the rst coat. Apply in 4’ x 4’ sections.
Begin with the roller in the center of the section and roll
outwards in random directions. Avoid regular patterns and
knock down hard edges using the roller. Allow rst coat to
dry then apply second coat in the same method as the rst
coat. While two coats are necessary, additional coats may
help hide previous surface imperfections or cover over dark
colors. For large projects, consider using a texture sprayer
with a 4mm tip. Spray in 4’ x 4’ sections and back roll with
an adhesive roller cover.
SURFACE PREPARATION:
(Proper surface preparation is required.) All surfaces must
be clean, sound, dry and free of any dirt, oil, and grease.
For hairline cracks up to 1/8", completely ll in with coating
using a nylon/polyester brush and allow to dry completely
prior to roller application. Uncoated Concrete or Masonry
Surfaces: Allow new surfaces to cure 30 days. Clean and etch
surface using a product such as a muriatic acid etcher (read
and follow all manufacturer’s label and safety directions)
to achieve a textured prole similar to 150 grit sandpaper.
Previously Coated Surfaces: For a painted surface in
sound condition, use a product to clean and prepare the
surface. If the coating is failing or peeling, use a paint stripper
to remove old coating or scrape/sand down to a sound
concrete surface. Scu sand glossy surfaces. Clean and spot
etch any exposed concrete. Remove all dust with a damp
cloth, allow to dry.
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• DO NOT THIN.
• Intermix all cans of same product to ensure color
uniformity. Stir before applying.
• Use product when air and surface temperatures
are between 50-90° F.
• Do not apply in direct sunlight.
• Not for surfaces subject to vehicle trac or parking.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
COMPLIES WITH THE BELOW AS OF 12/1/15
SCAQMD YES OTC YES
CARB YES LADCO YES