TDS

Revised 6/2014
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 3/2019
2 of 2
Stain-Blocking: After priming, test for stain bleed-
through by applying the topcoat to a small section. If the
stain bleeds through the topcoat, apply a second coat of
primer and test again before top-coating the entire area.
If bleeding continues, a longer dry time of the primer may
be needed before top-coating. On stained surfaces, topcoat
in 4 hours; for heavy stains, topcoat in 16 hours. Two coats
may be needed over heavy stains and tannin-rich wood.
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps
with a 100% acrylic, siliconized, paintable caulking, and
allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For use on properly prepared exterior wood oors when
applying BEHR Porch and Patio Floor paint. Not for use on
concrete and masonry oors.
• For best results, apply at temperatures between 35°F -
90°F. Temperatures above 90°F may aect the dry time.
Avoid painting under direct sun.
• Surface temperature during application should be at least
5°F above dew point.
• Application of coating when the relative humidity is above
85% will adversely aect coating performance.
• Topcoat within 30 days.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
WARNING IRRITANT HARMFUL IF SWALLOWED.
CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT
TAKE INTERNALLY.
MULTISURFACE INTERIOR/EXTERIOR
STAINBLOCKING PRIMER & SEALER
NO. 436