TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
Stain-Blocking: After priming, test for stain bleed-
through by applying the topcoat to a small section. If the
stain bleeds through the topcoat, apply a second coat of
primer and test again before topcoating the entire area.
If bleeding continues, primer may need a longer dry time
before applying topcoat. On stained surfaces, topcoat in 4
hours; for heavy stains, topcoat in 16 hours. Two coats may
be needed over heavy stains and tannin-rich wood.
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate patching material. Let dry completely
and sand smooth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For use on properly prepared exterior wood oors when
applying BEHR® Porch and Patio Floor paint. Not for use on
concrete and masonry oors.
• For best results, apply when air, material and surface
temperatures are between 35°F and 90°F. Do not apply in
direct sunlight. Temperatures above 90°F can cause the
paint to dry too fast, whereas temperatures below 35°F
can inhibit proper lm formation.
• Surface temperature during application should be at least
5°F above dew point.
• Application of coating when the relative humidity is above
85% will adversely aect coating performance.
• Topcoat within 30 days.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY
CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS:
ETHYLENE GLYCOL, CRYSTALLINE SILICA AND TITANIUM
DIOXIDE. Avoid contact with skin and eyes and avoid
breathing vapors, spray mist and sanding dust.
Sanding, grinding or abrading may release sanding dust,
which may be harmful if inhaled and has been shown to
cause lung damage or cancer with long term exposure. Do
not breathe dusts, vapor, or spray mist. To avoid breathing
in dust, vapors, and spray mist, open windows and doors or
use other means to ensure fresh air entry during application,
drying, sanding, and/or abrading. If properly used, a
respirator (NIOSH approved with particulate pre-lter) may
oer additional protection and should be used if adequate
ventilation cannot be provided; obtain professional advice
before using. If you experience eye watering, headaches,
or dizziness during application or drying, increase fresh air
or leave the area. Avoid contact with eyes and skin. Wash
thoroughly after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experience, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE
INTERNALLY.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 9/2020
2 of 2
MULTISURFACE INTERIOR/EXTERIOR
STAINBLOCKING PRIMER & SEALER
NO. 436