Use and Care Manual

WARNING IRRITANT HARMFUL IF SWALLOWED. AVOID
CONTACT WITH EYES. MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID BREATHING OF DUST, VAPORS OR SPRAY
MIST. USE ONLY WITH ADEQUATE VENTILATION. Open windows and
doors or use other means to ensure fresh air entry during application and drying. If you experience
eye watering, headache or dizziness or if air monitoring demonstrates vapor / mist levels are
above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC-23C or
equivalent) during and after application. Follow respirator manufacturer’s direction for respirator
use. Close container after each use. Wash thoroughly after handling and before smoking and eating.
FIRST AID: If swallowed, do not induce vomiting. Get medical attention immediately.
If you experience difficulty in breathing, leave the area to obtain fresh air. If continued
difficulty is experienced, get medical attention immediately. In case of eye contact, flush
eyes immediately with plenty of water for at least 20 minutes and get medical attention.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
BEHR
®
Interior/Exterior
Bonding Primer
• Adheres to Tough-to-Paint Surfaces
• Reduces Need for Sanding Dense,
Glossy Surfaces
• Improves Topcoat Adhesion
• Works Under Alkyd, Oil and
Water-Based Topcoats
• Quick Recoat Time
• Tintable up to 2 oz.
of Colorant per Gallon
WHERE TO USE
Over properly prepared uncoated and previously painted interior or
exterior surfaces. Ideal for Kynar
®
, PVC, vinyl, Formica
®
, glass, tile,
glazed brick, fiberglass, chalky paints, glossy finishes, architectural
plastics, and metals. If using as a primer for epoxies, lacquers,
products containing xylene or other hot solvents, allow to dry for 24
hours before topcoating; test for compatibility in a discrete area first
before full coat application. Not recommended for floors or horizontal
surfaces subject to prolonged water contact.
PREPARATION
All surfaces must be properly prepared and cleaned. While BEHR
®
Bonding Primer is formulated to adhere without sanding, it is
recommended that a small area be tested for adhesion prior to
beginning the job. Remove loose paint, wash off chalk, dirt and
grease with detergent, rinse well and allow to dry. Remove mildew
stains with a mildew stain removing product. Remove all dust with
a damp cloth, allow to dry. Remove loose rust, peeling paint and
mill scale with a scraper, wire brush or sandpaper. Clean bare metal
surfaces in accordance with The Society for Protective Coatings
(SSPC) specifications.
APPLICATION
Apply when air and surface temperatures are between 50-90°F
(10-32°C). Use a high quality 3/8-1/2" nap roller cover on smooth
surfaces or 1/2-3/4" nap roller cover on semi-rough or porous surfaces,
nylon/polyester brush or an airless sprayer (.015"-.021" spray tip, 60
mesh filter). Stir primer occasionally. Do not thin if using a roller or
brush; however, if using a sprayer and thinning is required, thin with
water at a rate of no more than 1/2 pint per gallon. Topcoat within
14 days. For dramatic color changes, tint primer with up to 2 fl oz of
colorant per gallon.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit behr.com for painting tips, project advice and color coordination
with the ColorSmart by BEHR
®
Tool, or download the ColorSmart by
BEHR App on your mobile device.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
No. 432 White
©2019 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. < 100 g/L • REV. 05/19
30 Min Dries to Touch
1 Hr Ready to Topcoat
300-400 Sq. Ft.
Coverage per Gallon
*LIMITED WARRANTY For one year from the date of purchase, Behr Process Corporation warrants
to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s
manufacturing specifications, and (2) the performance of this product when applied according
to the label instructions and specifications. If this product is found not to perform as specified on
the label within one year from the date of purchase, Behr Process Corporation will, at its option
and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent
amount of new product or refund the original purchase price of this product to you. This warranty
excludes (1) labor and costs of labor for the application or removal of any product, and (2)
any incidental or consequential damages, whether based on breach of express or implied
warranty, negligence, strict liability or any other legal theory. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. To the extent permitted by applicable law, any implied warranties including
the implied warranties of merchantability and of fitness for a particular purpose, are limited to the
duration of this express warranty. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal
rights and you may also have other rights, which vary from state to state. Note to residents of
the State of New Jersey: The provisions of this warranty, including its limitations, are intended
to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain
warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect
any and all application of the product prior to processing your claim made under this warranty.
Protect
from Freezing
Soap & Water
Clean-Up
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov