TDS
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
TECHNICAL DATA SHEET
Revised 11/2015
1 of 1
OIL-LATEX REDWOOD STAIN
NO. 9
PRODUCT INFORMATION
BEHR® Oil-Latex Redwood Stain produces a deep, redwood tone, color stain that protects exterior wood surfaces.
The unique formula penetrates wood surfaces and remains exible to resist cracking, aking and peeling on properly
prepared surfaces.
RECOMMENDED USES:
Recommended for properly prepared new to moderately weathered, unsealed exterior wood surfaces such as:
• Wood • Plywood
• Pressured Treated Lumber
Do not use on horizontal surfaces subject to foot trac.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 9 128 oz.
Resin Type: Oil-Latex
Weight per Gallon: 9.7 lbs
% Solids by Volume: 21.6%
% Solids by Weight: 32.6%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 55-60 KU
Recommended Film Thickness:
Wet: 7.8 Dry: 1.7 mils @ 200 Sq. Ft./Gal.
Wet: 3.9 Dry: 0.9 mils @ 400 Sq. Ft./Gal.
Coverage: 200-400 Sq. Ft./Gal. depending on application
method and substrate porosity.
APPLICATION:
Brush: Natural Bristle
Roller: 3/8"-3/4" nap
Pad Applicator
Airless Spray: At packaged consistency
Tip: .015- .019"
Filter: 60 mesh
Dry Time: @ 77° & 50% RH
To Touch: 1 hour
To Recoat: 4 hours
• Follow spraying immediately with a pad, back brushing,
or back rolling for a uniform appearance.
• Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as
BEHR PREMIUM® Wood Stain & Finish Stripper No. 64 to
remove loose wood bers, latex, oil-based and 100% acrylic
coatings on new weathered wood, then you must use a
product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use a product such as BEHR PREMIUM Wood Stain & Finish
Stripper No. 64, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium stains caused
by mold, mildew, algae & fungus. Rinse thoroughly and
allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63 to
remove mill glaze and open the pores of the wood. Lightly
sand any remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying stain in direct sunlight or hot surfaces
• Test product for color on a small hidden area before
proceeding
• Over application of stain will lead to surface failure
including peeling & cracking
• Shelf life under normal conditions is two years
(unopened containers)
• Temperature Range: 40-90°F (4.5-32°C).
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, eye, and
face protection. Do not eat, drink, or smoke when using
this product. Take o contaminated clothing and wash it
before reuse. Wash hands thoroughly after handling.
Collect spillage and avoid release to the environment.
Dispose of unused, contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009)
†
YES