Use and Care Manual

BEHR PREMIUM
™
AEROSOL:
Metallic, Hammered,
and Textured Finishes
METALLIC
B060144 Gold
B060244 Oil Rubbed Bronze
B060544 Soft Iron
B060644 Vintage Gold
B060744 Nickel Satin
B060844 Titanium
B062044 Antique Copper
B061844 Dark Steel
B061744 Champagne Gold
B062244 Burnished Amber
HAMMERED
B060944 Hammered Black
B061044 Hammered Brown
B061244 Hammered Burnished Amber
B061344 Hammered Antique Pewter
B061444 Hammered Dark Bronze
B061644 Hammered White
B062344 Hammered Chestnut
TEXTURED
B061544 Black Matte Textured
• Indoor/outdoor use
• Corrosion Resistant
• Excellent Adhesion
Protect
from Freezing
15-30 Dry to Touch
<1 hr or greater
than 24 Recoat time
15-20 sq. ft.
Coverage
Mineral Spirits
Clean-Up
BEHR PREMIUM
™
Aerosol features an enhanced formulation that
combines paint and primer
†
in a single can, delivering a premium,
durable finish. Designed for both indoor and outdoor uses.
BEHR PREMIUM
™
Aerosol can be used on wood, metal, cast stone,
and wicker. Weather and corrosion resistant, it delivers a
reliable, long-lasting finish. The unique, ergonomic shape of the
BEHR PREMIUM
™
Aerosol can and its comfortable tip deliver a
superior spray experience that fights fatigue so you can create a
smooth finish every time.
†
A Primer coat may be needed on some surfaces.
PREPARATION
The surface must be clean, free of dust, grease, wax, peeling
paint, mold or mildew. If washing is necessary, use a non-soapy
detergent or a TSP substitute. Rinse well and allow to dry.
†
Peeling or Checked Paint: Scrape off loose paint and sand to
a smooth surface. Sanding or removal of paint containing lead
is hazardous.
*Glossy Surfaces: For maximum adhesion, scuff sand the
surface thoroughly before painting.
APPLICATION
Eye protection is recommended. For best results, use at room
temperature. Cover adjacent areas to protect from overspray.
Shake can vigorously for one minute after mixing ball begins to
rattle and often during use. Hold can upright, moving from side-
to-side while spraying lightly and evenly about 12” from area
being painted. Two to three thin coats produce best results.
CLEAN-UP & DISPOSAL
Clear spray valve immediately after use by turning can upside
down and spraying until only clear gas is released. If spray
nozzle becomes clogged, remove and clean. Do not stick pins or
wire into can opening. Clean fresh overspray with mineral spirits
or paint thinner. Remove dried paint with paint remover, but
test small area first to ensure paint remover does not damage
substrate. Please consider donating any unused product. For
recycling or disposal information contact your local household
refuse collection service.
Visit behr.com for painting tips, project advice and color coordination
with the ColorSmart by BEHR
®
Tool, or download the ColorSmart by
BEHR App on your mobile device.
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
*LIMITED WARRANTY For one year from the date of purchase, Behr Process Corporation
warrants to the original consumer purchaser, (1) that the product meets Behr’s manufacturing
specifications, and (2) the performance of this product when applied according to the label
instructions and specifications. If this product is found not to perform as specified on the label
within one year from the date of purchase, Behr Process Corporation will, at its option and upon
presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of
new product or refund the original purchase price of this product to you. This warranty excludes
(1) labor and costs of labor for the application or removal of any product, and (2) any
incidental or consequential damages, whether based on breach of express or implied
warranty, negligence, strict liability or any other legal theory. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. To the extent permitted by applicable law, any implied warranties including
the implied warranties of merchantability and of fitness for a particular purpose, are limited to the
duration of this express warranty. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal
rights and you may also have other rights, which vary from state to state. Note to residents of the
State of New Jersey: The provisions of this warranty, including its limitations, are intended
to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain
warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect
any and all application of the product prior to processing your claim made under this warranty.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
DANGER! EXTREMELY FLAMMABLE LIQUID AND VAPOR. VAPORS MAY CAUSE FLASH FIRE.
VAPOR HARMFUL. VENTILATION REQUIRED: To avoid inhalation and combustion hazards (see
below), DO NOT use this product unless you can achieve cross ventilation by opening windows
and doors during application and drying. MAY CONTAIN: ACETONE, BUTYL ACETATE, PROPANE,
ISOBUTANE, 1-METHOXY-2-PROPANOL ACETATE, METHYL ETHYL KETONE, 3-ETHOXYPROPIONIC
ACID ETHYL ESTER, ALUMINUM, STODDARD SOLVENT, SOLVENT NAPHTHA (PETROLEUM), ALIPHATIC
PETROLEUM DISTILLATES, CARBON BLACK, TITANIUM DIOXIDE and CRYSTALLINE SILICA. May affect
the brain or nervous system causing dizziness, headache or nausea. CAUSES SERIOUS EYE DAMAGE.
IRRITATES SKIN, NOSE AND THROAT. Do not breathe vapors or spray mist. If you experience eye
watering, headaches or dizziness, increase fresh air, wear respiratory protection (NIOSH/MSHA TC
23C or equivalent) or leave the area. VAPORS MAY IGNITE EXPLOSIVELY. Do not spray near sparks,
heat or open flame. Do not smoke. Vapors are heavier than air and can travel at floor level to distant
ignition sources. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors,
high intensity lights and other sources of ignition during use and until all vapors are gone. WARNING-
CONTENTS UNDER PRESSURE. Do not puncture or incinerate container. Do not expose to heat
or store at elevated temperatures above 120°F. Prolonged exposure to sun may cause bursting.
FIRST AID: If you have difficulty breathing, leave area to obtain fresh air. If difficulty continues, get
medical attention immediately. If swallowed, call physician immediately. In case of eye contact, flush
immediately with plenty of water for at least 15 minutes and get medical attention. For skin contact,
wash thoroughly with soap and water.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
©2021 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
REV. 11/21