SDS

Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without
risk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reduce
vapors or divert vapor cloud drift. Isolate area until gas has dispersed. Eliminate all ignition
sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood,
paper, oil, etc.) away from spilled material. Absorb in vermiculite, dry sand or earth and place into
containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid discharge into drains, water courses or onto the ground.
Environmental precautions
7. Handling and storage
Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when
handling the product must be grounded. Protect containers from physical damage; do not drag,
roll, slide, or drop. Do not re-use empty containers. Avoid breathing mist/vapors. Avoid contact with
eyes. Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate personal
protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene
practices.
Precautions for safe handling
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Store in tightly closed container. Store in a
well-ventilated place. Stored containers should be periodically checked for general condition and
leakage. Store away from incompatible materials (see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 2400 mg/m3Acetone (CAS 67-64-1)
1000 ppm
PEL 3.5 mg/m3Carbon black (CAS
1333-86-4)
PEL 590 mg/m3Methyl ethyl ketone (CAS
78-93-3)
200 ppm
PEL 710 mg/m3n-Butyl acetate (CAS
123-86-4)
150 ppm
PEL 1800 mg/m3Propane (CAS 74-98-6)
1000 ppm
US. ACGIH Threshold Limit Values
Form
ValueComponents Type
STEL 500 ppmAcetone (CAS 67-64-1)
TWA 250 ppm
TWA 3 mg/m3 Inhalable fraction.Carbon black (CAS
1333-86-4)
STEL 1000 ppmIsobutane (CAS 75-28-5)
STEL 300 ppmMethyl ethyl ketone (CAS
78-93-3)
TWA 200 ppm
STEL 150 ppmn-Butyl acetate (CAS
123-86-4)
TWA 50 ppm
BEHR Premium Gloss Hammered Black - Aerosol
959197 Version #: 1.5 Revision date: 23-November-2021 Issue date: 20-August-2021
SDS US
3 / 10