TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*For as long as you reside in your home. See label for details.
Revised 11/2015
1 of 2
INTERIOR/EXTERIOR HIGLOSS ENAMEL PAINT
NO. 8050 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR PREMIUM PLUS® Interior/Exterior Hi-Gloss Enamel Paint has a brilliant, glass-like sheen and is the perfect choice when
exceptional durability and easy stain removal is desired. Hi-Gloss Enamel is excellent for highlighting trim, railing, shutters
and molding. This 100% acrylic latex, mildew resistant nish oers exceptional hide and maximum moisture resistance.
RECOMMENDED USES:
For properly prepared and primed or previously painted substrates including:
• Concrete • Concrete Block/CMU • Brick • Plaster
• Drywall/Gypsum Board • Wood • Ferrous Metals • Galvanized Steel
• Aluminum • Other Non-Ferrous Metal • Architectural Plastics
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 8050 128 oz. / 2 oz.
No. 8400 120 oz. / 10 oz.
No. 8300 116 oz. / 14 oz.
Gloss: 75> @ 60°
Resin Type: 100% Acrylic Latex
Weight per Gallon: 10.5 lbs.
% Solids by Volume: 34%
% Solids by Weight: 49%
VOC: <150 g/L
Flash Point: N/A
Viscosity: 95-105 KU
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 2.2 mils @ 250 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.4 mils @ 400 Sq. Ft./Gal.
Coverage: 250-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller:
Smooth Surface: 3/8" - 1/2" nap
Rough Surface: 1/2" - 3/4" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint of
water per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust, and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior
to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material. Let dry
completely and sand smooth. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly before coating.
New Wood: Remove mill glaze with sand paper. Set nails
and ll holes, scratches, and gouges with the appropriate
wood ller and let dry completely. Remove all dust with a
wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating. Previously Painted Wood: Remove all loose and
peeling paint and all other foreign substances. Clean any dirt
and grease by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps
with a 100% acrylic, siliconized, paintable caulking,
and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize. Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material and
let dry completely and sand smooth. Remove all dust with
a tack or wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stainblocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before top-coating the entire area. If bleeding
continues, a longer dry time of the primer may be needed
before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower
prior to coating. Smooth masonry may require an
adequate prole for adhesion. For all other smooth
trowel concrete, create a prole using a product such
as a muriatic acid etcher or with mechanical means.
Remove all loose aggregate and debris.
Metals: Ferrous and Non-Ferrous Metals: All metals
should be clean and free of any oils, rust, mill scale or
other contaminants. All metals require sucient “tooth”
or prole for optimum adhesion and therefore require
some type of sanding, abrasion, or chemical etching.
Oil lms: (especially on new or non-ferrous metals)
should be removed by scrubbing the surface with a
COMPLIES WITH THE BELOW AS OF 10/1/2015
OTC YES MPI# 114, 119
LADCO YES GREENGUARD® YES
AIM YES CHPS YES
LEED v.3 (2009)
†
YES NAHB/ICC NGBS YES
LEED v.4
†
YES FLAME SPREAD/CLASS A YES
†
Please see www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.