User's Manual
Wireless USB Dongle
NANO Dongle / EMPREX,BTC
Quick Installation Guide
-For Windows® 2000 operating system, please go to http://www.emprex.com/ website to download and install the “KeyMaestro Input Device Driver”
to have the Multimedia Player functions.
-For Windows® XP and Windows Vista® operating systems, you could use the keyboard immediately after plugging the keyboard connector into the
PC. If you want to enjoy the full functionality of the keyboard, please visit our website at http://www.emprex.com/ to download and install the
“KeyMaestro Input Device Driver.” Once the driver has been installed, these hot keys are reprogrammable. They can be configured as a string, a
combination key, a web site, an existing file, or a function that the driver pre-defines for you.
1. Make sure the batteries of the keyboard and mouse are installed correctly. Please follow the polarity signs in
the battery compartment.
Front view of Back view of receiver
1. 2. Please make sure the slide switch on the back of the mouse is switched to “on”
receiver
before using the mouse. When not in use, please
turn the power switch to “off” for power saving.
2. 3. Plug the receiver directly into your available USB port on PC.
3. 4. Please hold the keyboard and mouse close to the receiver within 30 cm and press any key to pair ID, and then you can use
the wireless kit immediately.
Change the cursor pointer speed
You can modify the mouse pointer speed settings in the control panel.
1. 1. Open the Start Menu by clicking “Start” at the lower-left corner on the screen
2. 2. Then click on Settings / Control Panel / Mouse
3. 3. In the Mouse Properties window that appears, click the Motion tab
4. 4. Move the slide bar toward either the faster end or the slower end
5. 5. Click OK to exit and make the change effective
Please follow the hardware installation procedure mentioned above to install the wireless kit, and then you can use the wireless kit immediately. If it
can’t work, please Pairing/connect button on top follow the steps below to process ID setting of the wireless kit. of the receiver (With a LED
1. 1. Press the ID pairing/connect button on the top of the receiver at least 2 seconds indicator under the pairing/ until the receiver LED flashes.
The receiver LED will flash 60 seconds to wait for
connect button) keyboard and mouse pairing information. (If you release the button within 2 seconds,
the ID pairing will fail.)
2. 2. Next, hold the keyboard and press the ID pairing/connect button on the bottom of the keyboard at least 2 seconds until the LED
indicator on the upper right of the keyboard flashes once. (If you release the button within 2 seconds, the ID pairing will fail.)
3. 3. Then, press the ID pairing/connect button on the top of the receiver as step 1.
4. 4. Finally, hold the mouse and press the ID pairing/connect button on the bottom of
Pairing/connect button on the
the mouse at least 2 seconds until
the LED indicator flashes once. (If you release
bottom of the keyboard the button within 2 seconds, the ID pairing will fail.)
Note:
- When doing the pairing procedure, please hold the keyboard or mouse close to
Power Switch
the dongle receiver within 30 cm. -Each procedure should be completed within 60 seconds. -Make sure your PC is on and running when doing
the pairing procedure.
ID pairing button /
-You don’t have to pair ID again after changing batteries.
connect button
-Both the keyboard and mouse can operate
freely up to a radius of about 10m
from the receiver.
Pairing/ connect button on the
-Keyboard battery life is up to 15 months and mouse battery life is up to 6 months. It
bottom of the mouse
depends on the intensity of usage.
Available USB port
CD-ROM drive (for CD and Video operation)
Standard sound card (for CD and Video operation)
Microsoft® Internet Explorer 5.0 or later version (for the Internet keys)
Microsoft® Windows® 2000, Windows® XP or Windows Vista® operating system
The system supports ACPI or APM II (for power management buttons)