9116URF Wireless Keyboard with Joystick Manual Version 1.
封面內頁 FCC GUIDELINES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
Table of Contents Important Information................................................................................................... 2 1 Battery Installation ............................................................................................. 2 2 Receiver cable positioning................................................................................ 2 1 Introduction ............................................................................................................
Important Information 1 Battery Installation Please follow the instructions to install the batteries correctly. 1.1 Open the battery compartment cover on the bottom of the keyboard. 1.2 Follow the indication inside to place in keyboard batteries. 1.3 Place the battery compartment cover back and proceed with ID setting of the devices. Important: We recommend using alkaline batteries for a longer battery life. Always change batteries when battery low icon appears.
1 Introduction Congratulations on your purchase of this wireless USB RF keyboard with mouse & dual mode joystick mouse (with mouse & joystick functions). This wireless keyboard kit will not only free you of the constraints of your desktop, but also provide you dual mode: mouse & joystick functions for Internet browsing and game playing.
2 System Requirements Microsoft Windows 98, Windows ME, Windows 2000 or Windows XP operating system Microsoft Internet Explorer 5.0 or later version (for the Internet keys) CD-ROM drive (for CD and Video operation) Standard sound card (for CD and Video operation) The system supporting ACPI or APM II (for power management buttons) ATX mother board and ATX power supply (for power management buttons) Available USB port Please refer to table below for the other system requirements for the features.
3 Hardware Installation 3.1 Connecting and Battery Information Step 1: Plug in the receiver connector into your available USB port on PC. Front View of USB Connector Back View of USB Connector Plug the USB connector into PC USB port. Step 2: Take the keyboard and make sure the batteries on the back are installed correctly. (Follow the polarity signs in the battery compartment.) 1 .5 V * 2 ID B u tto n Bottom view of 9116URF keyboard Remarks: 1. The keyboard uses 2pcs standard UM-3 (AA) 1.
3.2 ID Setting This wireless RF keyboard kit contains 255 sets ID. This extra ID-recognition function helps to protect against interference from other RF keyboards in the same environment. This wireless RF keyboard kit comes preset with default ID. Under this circumstance, you can use this default ID setting and begin using the keyboard kit immediately after the installation. However, we still recommend following the steps below to set ID again to ensure the usage is fluent.
Remarks: 1. You must follow the procedure above to set ID of receiver, and then keyboard. After the receiver ID button is pressed, you have 1 minute to complete the entire process, from the moment when ID button on receiver is pressed (step 1), until ID button on keyboard is pressed (step 2) also, or you will need to begin again. 2. If the keyboard does not work after ID setting procedure, or the signal transmission between the receiver and keyboard is interrupted, please re-proceed ID setting procedure.
4 Software Installation 4.1 Driver installation After finishing the hardware installation, you should be able to immediately take advantage of the wireless function of the wireless keyboard. If the keyboard does not work properly, see Chapter 6: Troubleshooting for tips on how to solve your problem. If your operating system is Windows ME, Windows 2000 or Windows XP, you can immediately take advantage of the extra function buttons on the keyboard (except ‘Eject key’).
5 Using the Keyboard and Joystick Mouse 5.1 Keyboard Functions Besides the usual keys, this keyboard also has extra-dedicated keys. Which provide the following hot key functions. The functions are described as below: Please Note: In order to use these keys under Windows® 98, it is necessary to have “KeyMaestro Input Device Driver” installed. Please refer to Chapter 4: Software Installation for more information. Back Return to the last page you viewed. Forward View the next page you viewed before.
5.2 Using Keyboard Embedded Numeric Keypad The embedded numeric keypad consists of 16 keys and different functions in three ways. Note: Please install “KeyMaestro Input Device Driver” to show LED (NumLock) indication. As a part of the main keyboard. * As a numeric keypad. As a cursor movement keypad.
There are two keys to activate the embedded numeric keypad: 1. NumLock: This is a toggle key. Press this key and toggle NumLock LED indicator. If NumLock LED indicator (located on system tray) is on, then the embedded numeric keypad function is activated. 2. Shift: This key can be pressed together with the keys on embedded numeric keypad when NumLock LED indicator is on to switch as a cursor movement keypad. For accessing the embedded numeric keypad, please refer to following table: 1.
5.3 Using the Joystick “Joystick Function” can only be used when playing computer games. Press “Fn + F12 ” to switch to “Joystick Function” When switching to Joystick Mode, an tray. 5.4.1 icon will appear on Windows system Joystick Buttons Default Setting: Button 1: Mouse Left Button Button 2: Mouse Right Button 1. Cursor movement Joystick 2.
5.4.2 Joystick Functions Specially Important: 1. “Joystick Function” can only be used when playing computer games. Press “Fn + F12 2. ” to switch to “Joystick Function” Before starting to use the joystick, please go first to “Start → Settings → Control Panel → Game Controllers → General → Properties → Test” to check the axes direction and buttons are functioned well. 3.
6 Troubleshooting If you are experiencing problems with your keyboard, please check the following: 1. Take out the receiver’s connector and check both the receiver’s keyboard plug for possible broken pins. If the plugs appear normal then reinsert the plugs into their respective connectors on your PC. 2. Check to see if the batteries in the keyboard are installed correctly. Make sure the polarity of the batteries corresponds with the polarity signs in the battery compartment. 3.
封底內頁 11. If you can’t aim an object in a game easily, please calibrate the joystick. Go to “Start → Settings → Control Panel → Game Controllers → General → Properties → Settings → Calibrate” 12. When the game can’t recognize the joystick and or the joystick can’t be used in the game, please check the following: - Press “Fn + F12 ” again to see if the function is switched to joystick. - Go to “Start → Settings → Control Panel → Game Controllers → Advanced” to check if the joystick is assigned to ID 1.
封底 3100506170 Version 1.0 Jan.
