hp pavilion home pc Installing the Wireless Keyboard and Mouse Set Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
Installing the Wireless Keyboard and Mouse Set A The wireless keyboard and mouse set consists of a receiver (A) that plugs into the computer, a wireless keyboard (B), and a wireless mouse (C). B Note: This wireless set is compatible with your HP Pavilion home PC and not intended for use with other computers. C Note: You can replace the batteries in the mouse and keyboard without turning off the computer. The computer must be on to change the ID setting on the three units.
Getting the Mouse Ready Note: Do not use rechargeable batteries in the mouse. Alkaline batteries are recommended. K E E1 K E 2 E1 HP Pavilion home PC Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
Install the two AA alkaline batteries (provided) in the wireless mouse: Push in at E1 and lift the battery cover (E) from the bottom of the mouse, and then insert the batteries into the compartment. Note the battery icons, and make sure batteries are placed in the correct direction. Replace the cover. Note: The red LED (K) turns on indicating the batteries are installed correctly. HP Pavilion home PC Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
Getting the Keyboard Ready G Note: Do not use rechargeable batteries in the keyboard. Alkaline batteries are recommended. H I I G H J 4 HP Pavilion home PC Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
1Install the two AA alkaline batteries (provided) in the wireless keyboard: Remove the cover (G) from the bottom of the keyboard, and insert the batteries into the compartment (H). Note the battery icons, and make sure batteries are placed in the correct direction. Replace the cover. 2Adjust the keyboard height by lifting the adjustment bar (JI). Getting the Receiver Ready The receiver (A) must be placed upright and positioned properly to avoid interference from other electrical equipment.
L A A L M 6 3Set the receiver upright and follow these guidelines. nA: Minimum 20 cm (8 inches) clearance between the receiver and other electronic devices. nB: Maximum 1.5 m (59 inches) working distance between the receiver and wireless mouse or wireless keyboard. HP Pavilion home PC Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
nC: Minimum 20 cm (8 inches) clearance between the receiver and the monitor. nPlace no electronic device between the receiver and wireless mouse or wireless keyboard. Note: This is one example of the setup. Other setup positions are also possible. Warning: To avoid causing interference, keep the receiver at least 20 cm (8 inches) away from the monitor. HP Pavilion home PC Filename: 5219urf users guide US_revised(p11).doc Title: hp pavilion home pc Template: Normal.
Setting Up the Wireless Set The mouse and keyboard have 255 IDs that are randomly selected when you press the ID button. This helps protect against interference from other wireless devices in the same area. The top activity LED (N, a blue light) on the receiver will start flashing and will continue flashing until the next step are completed or until 30 seconds pass. Important: The word CONNECT labels the ID button on the bottom of each unit.
F K N O P Q Mouse 3 On the bottom of the mouse, press the ID button (F) once with a blunt pointed object. The mouse sends a new ID and flashes the mouse sensor LED (K) three times. The receiver flashes the blue top activity LED (N) three times and then stops to show it has accepted the new ID for the mouse. Note: At this time, when you move the mouse across a surface, the blue activity LED (N) on the receiver will go on and off indicating the mouse and the receiver are working together.
Receiver 4 On the bottom of the receiver, press the ID button (D) once with a blunt pointed object. The top activity LED (N, a blue light) on the receiver will start flashing and will continue flashing until the next step are completed or until 30 seconds pass. Keyboard 4 5 On the bottom of the keyboard, press the ID button (J) once with a blunt pointed object. The keyboard sends a new ID.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
