Datasheet

ManualsBrandsBEHA AMPROBE ManualsTest & MeasurementCurrent clamp, Handheld multimeter digital ACD-10 PLUS-D CAT III 600 V Display (counts): 4000

www.amprobe.eu

Data Sheet

Electrical Speciﬁcation Accuracy (23 °C ± 5 °C & < 75% R.H.), cont.

ACD-10 PLUS 600A Clamp-On Multimeter

Function Range Accuracy

AC Current (Clamp-on 50Hz / 60Hz)

Range Accuracy

1) 2) 3)

40.00, 400.0, 600 A ±( 1.5% + 8 digits)

Overload Protections: ACA Clamp-on jaws : 600 A rms continuous

ACD-10 Plus: Average Sensing

Max Induced error from adjacent current carrying conductor: 0.05 A

Speciﬁed accuracy is from 1% to 100% of range and for measurements made at the jaw center. When the conductor is not positioned

at the jaw center, position errors introduced are: Add 2% to speciﬁed accuracy for measurements made BEYOND jaw marking lines

(toward jaw opening)

Add 8 digits to speciﬁed accuracy @ reading < 10% of range

Resistance

400.0 W ±( 0.8% + 8 digits)

4.000, 40.00, 400.0 kW ±( 0.6% + 4 digits)

4.000 MW ±( 1.0% + 4 digits)

40.00 MW ±( 2.0% + 4 digits)

Open Circuit Voltage : 0.4 VDC typical

Transient protection : 6.5 kV (1.2/50μs surge)

Frequency

Function Sensitivity (Sine RMS) Range Accuracy

400.0 mVac 350mV 1 0 Hz ~ 2 kHz ±( 0.5%+4 digits)

4.000 Vac 1V 5 Hz ~ 5 kHz ±( 0.5%+4 digits)

4.000, 40.00 Vac 32V 5 Hz ~ 100 kHz ±( 0.5%+4 digits)

400.0 Vac 90V 5 Hz ~ 10 kHz ±( 0.5%+4 digits)

600 Vac 500V 5 Hz ~ 5 kHz ±( 0.5%+4 digits)

400.0 Aac 60A 40 Hz ~ 400 Hz ±( 0.5%+4 digits)

Display counts: 5000

Resolution: 0.001Hz

Overload Protection : ACA Clamp-on jaws : AC 600A rms continuous

Transient protection : VAC input jacks : 6.5kV (1.2/50μs surge)

Capacitance

Range

Accuracy

2) 3)

500.0nF, 5.000μF, ±( 3.5% + 6 digits)

50.00μF, 500.0μF, 3000μF

1) Additional 50.00nF range accuracy is not speciﬁed

2) Accuracies with ﬁlm capacitor or better

3) Speciﬁed with battery voltage above 2.8V (approximately half full battery).

Accuracy decreases gradually to 12% at low battery warning voltage of approximately 2.4V

Transient protection: 6.5 kV (1.2/50 μs surge)

Audible Continuity Tester

Audible indication: between 10 W and 120 W.

Transient protection: 6.5 kV (1.2/50 μs surge)

Diode Tester / Open Circuit Voltage Test Current

(Typical) < 1.6 VDC @ 0.25 mA

Transient protection: 6.5 kV (1.2/50 μs surge)

Max Hold* (where applicable)

Speciﬁed accuracy ± 50 digits for changes > 25 ms in duration