iMove 8W Moving Wash Innovation , Quality , Performance WWW.BEGLEC.
7. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which TABLE OF CONTENTS the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. 1. Safety Instruction Ÿ Clean with soft cloth using normal glass cleaning fluid. Ÿ Always dry the parts carefully. 2.
1. Safety Instruction Pay attention to the belt tension when install the belt. Please read carefully the instruction, which includes important information about the installation, usage and maintenance. Please refer to the photos below: WARNING l Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. l Unpack and check carefully there is no transportation damage before using the unit.
Warning G. If The pan belt is broken l 1. Turn off the main power. To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. 2. Unscrew all the screws (A) and open the base-housing cover (B). l Never touch bulb with bare fingers, as it is very hot after using. 3. Unplug all the connect wires (C) that from the arm to PC board and igniter. l Hot lamp explosion hazard. Do not open the unit within five minutes after switching off. 4.
2. Technical Specification 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some Power supply - AC 120V ~ 60Hz / 230V ~ 50Hz suggestions for easy troubleshooting: Lamp - Discharge lamp MSD 250/2 GY 9.5 A. The unit does not work, no light and the fan does not work 1. Check the connect power and main fuse. Optical system - High efficiency optical system 2. Measure the mains voltage on the main connector.
5.5. DMX512 Connection 8 Channels: The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. Channel 1 = Pan motion Channel 2 = Tilt motion Channel 3 = Shutter Channel 4 = Effect wheel Channel 5 = Color Channel 6 = CYM Mix Color Channel 7 = Dimmer Channel 8 = CMY Speed Dimension: 397 x 360 x 512 mm (L x W x H) Weight: 27 kg Luminous intensity: 1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter. 2.
3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp. Discharge lamp: MSD 250/2 GY 9.5 1.
5.4. DMX512 Configuration 4. How To Set The Unit 4.1. Control Panel Display To show the various menus and the selected functions .
4.2. Main Function Stand by To select any of the pre-set functions, press the MENU button up to when the required one is shown on the display. Select the function by ENTER button and the display will blink. Use Function DOWN and UP button to change the mode. Once the required mode has been selected, press the ENTER button to setup or it will automatically return to the main functions without Mode any change after idling 8 seconds.
5. How To Control The Unit Channel Mode You can operate the unit in three ways: Press the MENU button up to when the is shown on the display. Pressing 1. By master/slave built-in preprogram function ENTER button and the display will blink. Use DOWN and UP button to select the 2. By easy controller (16 Channel ) or (8 Channel) mode. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any 3.
Display Inversion Blackout Mode Press the MENU button up to when the It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to is shown on the display. Pressing ENTER (display inversion), It will automatically store after 8 seconds. Or press the ENTER blackout) or (no blackout) mode.
