Technical Specifications Power AC 120V~60Hz AC 230/240/250V~50/60Hz Fuse 20mm Glass T6.3A Fast Blow 20mm Glass T5A Fast Blow Lamp ELC 24V 250W Dimension 290mm x 330mm x 380mm Weight 12 kg IM-5S Innovation , Quality , Performance IM-5W User Guide WWW.BEGLEC.
7. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 20 days.
. . G. If The pan belt is broken 1. Turn off the main power. 2. Unscrew all the screws (A) and open the base-housing cover (B). TABLE OF CONTENTS 3. Unplug all the connect wires (C) that from the arm to PC board and ignitor. 1. Safety Instruction 4. Unscrew the screws (D) that fix the axis gear (E). 5. Change a new belt (F) by going through all connect wires that from the arm to base, 2. Technical Specification and through the bridge for correct position. 2.1 Beam Angel 6.
1. Safety Instruction 6. Troubleshooting Please read carefully the instruction, which includes important information Following are a few common problems that may occur during operation. Here are about the installation, usage and maintenance. some suggestions for easy troubleshooting: WARNING ♦ A. The unit does not work, no light and the fan does not work Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
. 5.5 DMX512 Connection The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 1 2 3 Warning 4 ♦ To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. ♦ Never touch bulb with bare fingers as it is very hot after using. ♦ Hot lamp explosion hazard. Do not open the unit within five minutes after switching off. ♦ Do not start on the unit without bulb enclosure or housing are damaged.
2. Technical Specification 5.4 DMX512 Configuration • Voltage：AC 120V~60Hz or 230V/240V/250V~50/60Hz • Bulb：ELC 24V 250W • The unit is DMX512 fixture. It features full DMX512 control. It can be also linked together in master/slave connection, as many as required and run by built-in program chase sequences automatically or by sound activation through an internal microphone to create an intelligent effect. • It can be operated by DMX512 control or can be used as an individual unit without a controller.
Stand by IM-5S IM-5W 3. Lamp Blackout the unit Strobe 1.Gobo / Color sync. strobe 2.Sync. strobe 3.Two-light strobe X/Y moving show mode Color/Gobo selection 1. Hold on for gobo selection change. ( Show 1 ~ Show 4 ) Please refer to Show mode 2. Press shortly for color change in 4.2 Main Function X/Y moving setting 1.Pan position 2.
4. How To Set The Unit 5. How To Control The Unit 4.1 Control Panel You can operate the unit in three ways: 1. By master/slave built-in preprogram function 2. By easy controller 3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be effected at once.
4.2 Main Function Display Inversion To select any of the given functions, press the MENU button up to when the required one is It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to showing on the display. Select the function by ENTER button and the display will blink. Use when the DOWN and UP button to change the mode. Once the required mode has been selected, is blinking on the display.
Press the MENU button up to when the Show Mode Press the MENU button up to when the is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (split color) mode. Once the mode has been selected, press the (normal) or ENTER button to setup or automatically return to the main functions without any change (show 1) after 8 seconds.
