,QVWDOODWLRQ JXLGH 1. 2. 3. 4. 5. ”Symbols used in the installation guide” on page 25 ”Connection diagram for the navigation system” on page 26 ”Installation of the GPS antenna” on page 27 ”Connecting the reverse signal” on page 29 ”Connecting the speed signal (GAL) for the speedometer / speedometer cable” on page 29 6. ”Installing and commissioning Traffic Pro” on page 34 7. ”Using GPS for the first time, and sensors” on page 34 8. ”Installation of the Navigation Software” on page 36 9.
,QVWDOODWLRQ JXLGH G Note the safety instructions of the vehicle manufacturer (airbags, immobilisers etc.). • When routing the cables, ensure that they cannot become jammed, kinked or ripped out. • Before installation, park the vehicle in a safe and level place and remove the ignition key. • If using branch connections, it is important to note the relevant cable section.
,QVWDOODWLRQ JXLGH ,QVWDOODWLRQ RI WKH *36 DQWHQQD G People with pacemakers should avoid physical contact with the magnetic antenna and should not carry the antenna on their person, as this may affect the function of the pacemaker. Keep the magnetic antenna away from data storage media (disks, credit cards, magnetic cards etc.) and electronic and precision engineering equipment, as this may cause data to be deleted. Do not use the antenna in areas at risk of explosion.
,QVWDOODWLRQ JXLGH a. Secure the antenna to the base plate (1) with magnets. b. Remove protective strip from top of adhesive tape (2) and stick to the centre of the base plate underside. c. Remove protective strip from bottom of adhesive tape (2) and stick the antenna and base plate onto the vehicle console beneath the windscreen at the installation position. ) GPS reception can be affected by screens with screen antenna, windscreen heating or thermally insulated screens.
,QVWDOODWLRQ JXLGH &RQQHFWLQJ WKH UHYHUVH VLJQDO ,I WKH VZLWFK RQ WKH JHDUER[ RU VKLIW OLQNDJH LV DFFHVVLEOH • Connect a separate lead to the activated contact. Connect the lead to socket A pin 2. /RZ OHYHO HDUWK KLJK OHYHO 9 9 $ ,I WKH VZLWFK LV QRW DFFHVVLEOH • Check which lead is routed to the reversing lamp. Then, if necessary, remove the inner cover for the reversing light. Connect a separate lead to the activated lead of the reversing lamp and connect to socket A pin 2.
,QVWDOODWLRQ JXLGH 0HFKDQLFDO VSHHGRPHWHU ZLWK LQWHJUDWHG VSHHG VHQVRU LQ WKH VSHHGRPHWHU FDEOH • Remove the signal from the speed sensor, extend and connect to socket A pin 1. • Minimum requirement for the signal: +] N+] VTXDUH ZDYH VLJQDO QR LQGXFWLYH VHQVRU /RZ OHYHO 9 KLJK OHYHO 9 9 ) *$/ VLJQDO $ If you do not know the exact installation position / location of the speed signal, please consult the vehicle manufacturer.
,QVWDOODWLRQ JXLGH ,QVWDOOLQJ WKH VSHHG VHQVRU GLUHFWO\ RQ WKH JHDUER[ • Release the speedometer cable and screw speed sensor onto gearbox. Screw released speedometer cable onto the speed sensor and connect the wires.
,QVWDOODWLRQ JXLGH Recommended tool: Cable installation tool for speedometer cables from VDO, order number: 1999.10.13.000.110 If you require vehicle-specific parts, please consult the vehicle manufacturer or your nearest VDO branch. • Using a metal saw, saw into the cable approx. 1 mm at right angles to the profile and break off (Figure 3). • Then cut the cable in the centre with side-cutting pliers (Figure 4).
,QVWDOODWLRQ JXLGH ) When pressing in, ensure that the dog is securely positioned and that it runs smoothly. • Pull the hose sleeve and nut as far as possible in the direction of the dog, to achieve approx. 1-2 mm play (Figure 10). Slightly squeeze the hose sleeve with pliers. Wrap with isolating tape to secure (Figure 11). • Screw the connecting piece and the speed sensor into the cable (Figure 12). • Connect speed sensor using the extension cable from VDO (part number: 2152.90 30 0100).
,QVWDOODWLRQ JXLGH ,QVWDOOLQJ DQG FRPPLVVLRQLQJ 7UDIILF 3UR • This navigation system has an integrated universal bracket for DIN installation slots. An installation frame is not required. The unit is inserted into the installation slot and secured with the slides supplied. Further information is given in the operation guide in the chapter, "Installation and removal instructions". ) • 7KH LQVWDOODWLRQ DQJOH RI WKH XQLW PXVW QRW H[FHHG WR YHUWLFDO Connect the battery.
,QVWDOODWLRQ JXLGH • Engage the reverse gear for the reverse signal function test. ) • 7,,+ The arrows under 09,*;065 must change direction on engaging the reverse gear. When using the GPS for the first time, the vehicle must be parked outdoors, while ensuring that it has a clear view in all directions (not in the immediate vicinity of buildings). Information on the GPS reception is given in the right-hand part of the display.
,QVWDOODWLRQ JXLGH GPS antenna must be checked. • The menu for initial GPS start-up and for the sensor test is quit by simultaneously pressing the multifunction button and the multifunction button. 7,,+ 09,*;065 VMN P P P ,QVWDOODWLRQ RI WKH 1DYLJDWLRQ 6RIWZDUH 1DY • Press the button. • Insert the Navigation CD to install the software for the navigation system. • After the navigation software has been installed, the adjacent display appears.
,QVWDOODWLRQ JXLGH &DOLEUDWLRQ After commissioning, a calibration journey is required. During the journey, the speed signal (GAL) is automatically adapted to the vehicle-specific data and the gyro sensor is automatically adapted to the installation position of the unit. The distance to be covered depends on the type of vehicle and the local conditions. ) • The navigation system is only ready for operation on completion of the calibration journey. The main navigation menu is displayed.
,QVWDOODWLRQ JXLGH If, even after a relatively long period of time, the display with the request ! ! ! does not appear, then you should check the GPS reception conditions again (as under Service Mode in the Section ”Function test of GPS antenna ( )” on page 40). As soon as the display with the request ! ! ! appears, the calibration ride can be started. ) • A calibration ride can also be performed in a non-digitised area.
,QVWDOODWLRQ JXLGH ) If the unit is switched off during the calibration ride, language installation is requested when the unit is switched on again. Reinstallation can be skipped by pressing the 1DY button. !Y & • • Calibration has been completed successfully if the main navigation menu is displayed. Y Y Y For correct navigation on routes with time-dependent traffic guidance, the time should be set correctly as described under "System settings" in the operation guide.
,QVWDOODWLRQ JXLGH The following functions can be selected in the Service Mode: • - GPS function test • ! - function for deleting the calibration or for setting a calibration • ! - display for calibration ride • " ! ! - internal component test • - sensor function test • ! ! - voice test • - demo mode selection • # - the status of the Navigation CD is displayed By turning the right rotary control , select the desired entry (large letters) an
,QVWDOODWLRQ JXLGH &KDQJLQJ WKH FDOLEUDWLRQ ! Deleting the calibration: If the navigation system is removed from one vehicle and installed in another, it must be calibrated. However, to do so, the current calibration data must be deleted. In the Service Mode, select ! using the right rotary control and press to confirm. Using the right rotary control select ! and press to confirm. The calibration is deleted and the unit returns to the Service Mode.
,QVWDOODWLRQ JXLGH ) Unit rotation corresponds to horizontal rotation. A positive value means rotation of the front of the unit towards the driver (LHD). The unit inclination can now be selected in degrees by turning the right rotary control and pressing to confirm. ) " ! ! Unit inclination corresponds to vertical inclination. A positive value means upward inclination of the front of the unit.
,QVWDOODWLRQ JXLGH Enter the correct tyre size using the right rotary control and confirm the entry by pressing for more than 2 seconds. "! !& P !& ' TTTFTTTFTTT ) The letter "R" cannot be entered. 3 numbers must be entered before and after the slashes. Insert a "0" for any missing numbers.
,QVWDOODWLRQ JXLGH 6WDWXV RI FDOLEUDWLRQ ULGH ! In the Service Mode, select ! using the right rotary control and press to confirm. The calibration status (e.g. ! ! P ) and the type of positioning (e.g. ) are displayed. After completing calibration, the street in which you are currently driving is displayed (provided that it is digitised) instead of $ and #Y .
,QVWDOODWLRQ JXLGH • Engage the reverse gear for the reverse signal function test. ) • The number after #YP should jump from to ( to ). Drive round a bend to test the function of the internal sensors. ) The values after %P and &P should change. In order to quit the sensor test, press the back to the Service Mode. 1DY button. The unit switches 7HVWLQJ WKH YRLFH ! ! A test program is used to test the voice.
,QVWDOODWLRQ JXLGH 'HPR 0RGH The demo mode is intended for demonstration purposes. A fixed location is given to the unit (Hamburg Werderstaße). • In the Service Mode, select S using the right rotary control and press to confirm. Select between and by briefly pressing the right rotary control . By holding down the right rotary control , the selection is confirmed. • You can now enter a destination as described in the operation guide.
,QVWDOODWLRQ JXLGH &RQQHFWLRQV C1 C2 C3 B $QWHQQD EXVKLQJ A *36 DQWHQQD 6RFNHW & &RQQHFWLRQ LQVWUXFWLRQV 6RFNHW $ 1 2 3 4 5 6 7 8 1 2 3 4 5 6 Speed signal (GAL) Reversing lamp signal Telephone mute / clearing function Permanent positive (terminal 30) Control output for automatic antenna/amplifier Illumination (terminal 58) Switched positive (terminal 15) Earth (terminal 31) 6RFNHW & 7-12 6RFNHW % 1 2 3 4 5 6 7 8 Special connection for Becker CD changer 6RFNHW & Loudspeaker rear right
