BEC 9900VA Active Ethernet Fiber 802.
BEC 9900VA Active Ethernet Fiber 802.11ac Gateway with VoIP PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE ONLINE USER MANUAL.
Quick Start Guide Front Panel LEDs LED STATUS DESCRIPTION Green System is up and ready Red System failure Green SFP fiber connection is ready Power SFP Interchangeable LAN/WAN Ethernet – WAN management & configuration via GUI (Default) Ethernet LAN: Connected to a gigabit Ethernet device. Green Gigabit LAN1 / EWAN Ethernet Port LAN 2 - 3 USB Wireless 2.4GHz / 5GHz WPS Phone (Configured via GUI) Ethernet WAN: Successfully connected to a broadband device, e.g.
BEC 9900VA Active Ethernet Fiber 802.11ac Gateway with VoIP Rear Panel Connectors INTERFACE MEANING 1 Wi-Fi Antenna Connectors Female RP-SMA connectors, total of 6. 2 Power Power on/off button. 3 4 Power Jack Manually screw the dual-band Wi-Fi antennas tight to each connector. Connect the supplied power adapter to this jack. (DC IN) SFP Insert and gently push a 1000Base SFP module until it snaps into the slot tightly.
Quick Start Guide Application Diagram Hardware Installation 1. Power Connection Plug in the supplied power adapter to the wall jack, the other side to the BEC 9900VA then power it ON the by pressing the Power on/off button.
BEC 9900VA Active Ethernet Fiber 802.11ac Gateway with VoIP 2. LAN Connection Plug the RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the any network devise’s Ethernet port. 3. WAN Link Interface and Connection BEC 9900VA supports failover and failback to another WAN interface, SFP or Ethernet WAN. 3.
Quick Start Guide 3.2 SFP Connection Insert then gently push the Mini-GBIC SFP module into the SFP cage until it us tightly locked to the cage, and then connect the fiber cable to the module. 4. Phone Connection Connect RJ-11 cable(s) to Phone1 and/or Phone2 to analog phone. Go to 9900VA web GUI to setup your VoIP account(s). You can place VoIP calls simultaneously once registered with a VoIP service.
BEC 9900VA Active Ethernet Fiber 802.11ac Gateway with VoIP 5. USB Connection FTP or Samba Server attached to the USB port. Simply plug in an external USB HD and do a setup in the web GUI.
Quick Start Guide Connecting to the Router The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1 ~ 192.168.1.253. Open a web browser and type http://192.168.1.254 in the URL address bar. URL Address bar: type http://192.168.1.254 The login prompt will appear. Input the default username and password. *This username / password may vary by different Internet Service Providers.
BEC 9900VA Active Ethernet Fiber 802.11ac Gateway with VoIP Step 3: Setup Wireless Connection Access Point: select Activated SSID: Assign a unique name Channel: pick from 1~11 Security Type: select a mode - Disable (No security) - WPA - WPA2 (Most secure one) - WPA / WPA2 (auto detect WPA mode with wireless clients) - WEP (Less secure one) Pre-Shared Key: key for wireless authentication - WPA / WAPA2 Share Key: Assign a key between 8 ~ 63 characters.
Quick Start Guide Troubleshooting 1. None of the LEDs are on when you turn on the router. Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support. 2. You have forgotten your router login and/or password. Try the default login and password, please refer to User Manual.
