BEC 6600AEL Gigabit LTE Multi-Service Router Quick Start Guide
BEC 6600AEL Gigabit LTE Multi-Service Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE ONLINE USER MANUAL.
Quick Start Guide Front Panel - LEDs / LTE Connectors 1 1 PORT 1 MEANING LTE Antenna Connectors LED Screw the supplied LTE antennas onto the antenna connectors on both sides. STATUS DESCRIPTION Green System is up and ready Red Boot failure Green Transmission speed is at Gigabit speed (1000Mbps) Orange Transmission speed is at 10/100Mbps Blinking Data being transmitted/received USB Green Connecting to hard drive for storage or file sharing, etc. Wi-Fi 2.
BEC 6600AEL Gigabit LTE Multi-Service Router Rear Panel – Ports / Connectors 4 1 2 3 5 6 7 8 1 * PORT MEANING Wi-Fi Antenna Connectors Screw the supplied Wi-Fi antennas onto the antenna connectors on both sides LTE Antenna Connectors Screw the supplied LTE antennas onto the antenna connectors on both sides 1 2 Insert the mini SIM card (2FF) with the gold contact facing down SIM Card Slot Push the mini SIM card (2FF) inwards to eject it By controlling the pressing time, users can achieve
Quick Start Guide Hardware Connection Back Panel Ports & Connectors Wi-Fi & LTE Antenna Setup 4
BEC 6600AEL Gigabit LTE Multi-Service Router Hardware Installation 1. Power Connection Plug in the supplied power adapter to the wall jack and the other side to the device. Power ON the 6600AEL by pressing the Power On/Off button. 2. LAN Connection Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports and the other side to an Ethernet device.
Quick Start Guide 3. WAN Link Interface and Connection BEC 6600AEL offers WAN failover and failback between multiple WAN interfaces. 3.1 4G/LTE Connection Slide the SIM card into the card slot of the device with the gold contact facing down. Make sure that the SIM card is slid into the bottom of the slot with a click. When removing the SIM card, press the SIM card again to eject from the card slot.
BEC 6600AEL Gigabit LTE Multi-Service Router 4. USB for Network File Sharing BEC 6600AEL has built-in FTP and Samba Servers, simply plug in an external USB HD then follow the instruction setup in the User Guide.
Quick Start Guide Quick Setup Your Router Wired Broadband Connection - Before start configuring the 6600AEL, make sure you have the Ethernet WAN connected with your Internet box or fiber line. The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1 ~ 192.168.1.253. Open a web browser and type http://192.168.1.254 in the URL address bar. URL Address bar: type http://192.168.1.
BEC 6600AEL Gigabit LTE Multi-Service Router Step 4: Setup Wireless Connection Access Point: select Activated SSID: Assign a unique name Channel: pick from 1~11 Security Type: select a mode - Disable (No security) - WPA - WPA2 (Most secure one) - WPA / WPA2 (auto detect WPA mode with wireless clients) - WEP (Less secure one) Pre-Shared Key: key for wireless authentication - WPA / WAPA2 Share Key: Assign a key between 8 ~ 63 characters.
Quick Start Guide Troubleshooting 1. None of the LEDs are on when you turn on the router. Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support. 2. You have forgotten your router login and/or password. Try the default login and password, please refer to User Manual.
RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
