User's Guide
Table Of Contents
- XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
- Technical specifications
- Hardware
- Configure the XBee/XBee-PRO S2C 802.15.4 RF Module
- Modes
- Operation
- AT commands
- Special commands
- Networking and security commands
- C8 (802.15.4 Compatibility)
- CH (Operating Channel)
- ID (Network ID)
- DH (Destination Address High)
- DL (Destination Address Low)
- MY (Source Address)
- SH (Serial Number High)
- SL (Serial Number Low)
- MM (MAC Mode)
- RR (XBee Retries)
- RN (Random Delay Slots)
- ND (Network Discovery)
- NT (Node Discover Timeout)
- NO (Node Discovery Options)
- DN (Discover Node)
- CE (Coordinator Enable)
- SC (Scan Channels)
- SD (Scan Duration)
- A1 (End Device Association)
- A2 (Coordinator Association)
- AI (Association Indication)
- DA (Force Disassociation)
- FP (Force Poll)
- AS (Active Scan)
- ED (Energy Detect)
- EE (Encryption Enable)
- KY (AES Encryption Key)
- NI (Node Identifier)
- NP (Maximum Packet Payload Bytes)
- RF interfacing commands
- Sleep commands
- Serial interfacing commands
- I/O settings commands
- D0 (DIO0/AD0)
- D1 (DIO1/AD1)
- D2 (DIO2/AD2)
- D3 (DIO3/AD3)
- D4 (DIO4)
- D5 (DIO5/ASSOCIATED_INDICATOR)
- D8 (DIO8/SLEEP_REQUEST)
- P0 (RSSI/PWM0 Configuration)
- P1 (PWM1 Configuration)
- P2 (SPI_MISO)
- M0 (PWM0 Duty Cycle)
- M1 (PWM1 Duty Cycle)
- P5 (SPI_MISO)
- P6 (SPI_MOSI Configuration)
- P7 (SPI_SSEL )
- P8 (SPI_SCLK)
- P9 (SPI_ATTN)
- PR (Pull-up/Down Resistor Enable)
- PD (Pull Up/Down Direction)
- IU (I/O Output Enable)
- IT (Samples before TX)
- IS (Force Sample)
- IO (Digital Output Level)
- IC (DIO Change Detect)
- IR (Sample Rate)
- RP (RSSI PWM Timer)
- I/O line passing commands
- Diagnostic commands
- Command mode options
- Operate in API mode
- API mode overview
- API frame specifications
- Escaped characters in API frames
- Frame descriptions
- TX Request: 64-bit address frame - 0x00
- TX Request: 16-bit address - 0x01
- AT Command frame - 0x08
- AT Command - Queue Parameter Value frame - 0x09
- Remote AT Command Request frame - 0x17
- RX Packet: 64-bit Address frame - 0x80
- Receive Packet: 16-bit address frame - 0x81
- RX (Receive) Packet: 64-bit address IO frame- 0x82
- RX Packet: 16-bit address I/O frame - 0x83
- AT Command Response frame - 0x88
- TX Status frame - 0x89
- Modem Status frame - 0x8A
- Remote Command Response frame - 0x97
- Regulatory information
- Load 802.15.4 firmware on ZB devices
- Migrate from XBee through-hole to surface-mount devices
- PCB design and manufacturing
XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
7
BD (Interface Data Rate) 86
NB (Parity) 87
RO (Packetization Timeout) 87
D7 (DIO7/CTS) 87
D6 (DIO6/RTS) 88
AP (API Enable) 88
I/O settings commands 89
D0 (DIO0/AD0) 89
D1 (DIO1/AD1) 89
D2 (DIO2/AD2) 90
D3 (DIO3/AD3) 90
D4 (DIO4) 91
D5 (DIO5/ASSOCIATED_INDICATOR) 91
D8 (DIO8/SLEEP_REQUEST) 92
P0 (RSSI/PWM0 Configuration) 92
P1 (PWM1 Configuration) 93
P2 (SPI_MISO) 93
M0 (PWM0 Duty Cycle) 94
M1 (PWM1 Duty Cycle) 94
P5 (SPI_MISO) 94
P6 (SPI_MOSI Configuration) 95
P7 (SPI_SSEL ) 95
P8 (SPI_SCLK) 95
P9 (SPI_ATTN) 96
PR (Pull-up/Down Resistor Enable) 96
PD (Pull Up/Down Direction) 97
IU (I/O Output Enable) 97
IT (Samples before TX) 97
IS (Force Sample) 98
IO (Digital Output Level) 98
IC (DIO Change Detect) 98
IR (Sample Rate) 99
RP (RSSI PWM Timer) 99
I/O line passing commands 99
IA (I/O Input Address) 100
T0 (D0 Timeout) 100
T1 (D1 Output Timeout) 100
T2 (D2 Output Timeout) 100
T3 (D3 Output Timeout) 101
T4 (D4 Output Timeout) 101
T5 (D5 Output Timeout) 101
T6 (D6 Output Timeout) 101
T7 (D7 Output Timeout) 101
PT (PWM Output Timeout) 102
Diagnostic commands 102
VR (Firmware Version) 102
VL (Version Long) 102
HV (Hardware Version) 102
DB (Last Packet RSSI) 103
EC (CCA Failures) 103
EA (ACK Failures) 103
DD (Device Type Identifier) 103
Command mode options 104
CT (Command mode Timeout) 104
CN (Exit Command mode) 104