User's Guide
Table Of Contents
- XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
- Technical specifications
- Hardware
- Configure the XBee/XBee-PRO S2C 802.15.4 RF Module
- Modes
- Operation
- AT commands
- Special commands
- Networking and security commands
- C8 (802.15.4 Compatibility)
- CH (Operating Channel)
- ID (Network ID)
- DH (Destination Address High)
- DL (Destination Address Low)
- MY (Source Address)
- SH (Serial Number High)
- SL (Serial Number Low)
- MM (MAC Mode)
- RR (XBee Retries)
- RN (Random Delay Slots)
- ND (Network Discovery)
- NT (Node Discover Timeout)
- NO (Node Discovery Options)
- DN (Discover Node)
- CE (Coordinator Enable)
- SC (Scan Channels)
- SD (Scan Duration)
- A1 (End Device Association)
- A2 (Coordinator Association)
- AI (Association Indication)
- DA (Force Disassociation)
- FP (Force Poll)
- AS (Active Scan)
- ED (Energy Detect)
- EE (Encryption Enable)
- KY (AES Encryption Key)
- NI (Node Identifier)
- NP (Maximum Packet Payload Bytes)
- RF interfacing commands
- Sleep commands
- Serial interfacing commands
- I/O settings commands
- D0 (DIO0/AD0)
- D1 (DIO1/AD1)
- D2 (DIO2/AD2)
- D3 (DIO3/AD3)
- D4 (DIO4)
- D5 (DIO5/ASSOCIATED_INDICATOR)
- D8 (DIO8/SLEEP_REQUEST)
- P0 (RSSI/PWM0 Configuration)
- P1 (PWM1 Configuration)
- P2 (SPI_MISO)
- M0 (PWM0 Duty Cycle)
- M1 (PWM1 Duty Cycle)
- P5 (SPI_MISO)
- P6 (SPI_MOSI Configuration)
- P7 (SPI_SSEL )
- P8 (SPI_SCLK)
- P9 (SPI_ATTN)
- PR (Pull-up/Down Resistor Enable)
- PD (Pull Up/Down Direction)
- IU (I/O Output Enable)
- IT (Samples before TX)
- IS (Force Sample)
- IO (Digital Output Level)
- IC (DIO Change Detect)
- IR (Sample Rate)
- RP (RSSI PWM Timer)
- I/O line passing commands
- Diagnostic commands
- Command mode options
- Operate in API mode
- API mode overview
- API frame specifications
- Escaped characters in API frames
- Frame descriptions
- TX Request: 64-bit address frame - 0x00
- TX Request: 16-bit address - 0x01
- AT Command frame - 0x08
- AT Command - Queue Parameter Value frame - 0x09
- Remote AT Command Request frame - 0x17
- RX Packet: 64-bit Address frame - 0x80
- Receive Packet: 16-bit address frame - 0x81
- RX (Receive) Packet: 64-bit address IO frame- 0x82
- RX Packet: 16-bit address I/O frame - 0x83
- AT Command Response frame - 0x88
- TX Status frame - 0x89
- Modem Status frame - 0x8A
- Remote Command Response frame - 0x97
- Regulatory information
- Load 802.15.4 firmware on ZB devices
- Migrate from XBee through-hole to surface-mount devices
- PCB design and manufacturing
XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
6
Directed node discovery 64
Directed node discovery in compatibility mode 64
Destination Node 64
Remote configuration commands 65
Send a remote command 65
Apply changes on remote devices 65
Remote command responses 65
AT commands
Special commands 67
WR (Write) 67
RE (Restore Defaults) 67
FR (Software Reset) 67
Networking and security commands 67
C8 (802.15.4 Compatibility) 67
CH (Operating Channel) 69
ID (Network ID) 69
DH (Destination Address High) 69
DL (Destination Address Low) 70
MY (Source Address) 70
SH (Serial Number High) 70
SL (Serial Number Low) 70
MM (MAC Mode) 71
RR (XBee Retries) 71
RN (Random Delay Slots) 72
ND (Network Discovery) 72
NT (Node Discover Timeout) 73
NO (Node Discovery Options) 73
DN (Discover Node) 74
CE (Coordinator Enable) 74
SC (Scan Channels) 75
SD (Scan Duration) 75
A1 (End Device Association) 76
A2 (Coordinator Association) 77
AI (Association Indication) 78
DA (Force Disassociation) 78
FP (Force Poll) 78
AS (Active Scan) 79
ED (Energy Detect) 80
EE (Encryption Enable) 80
KY (AES Encryption Key) 81
NI (Node Identifier) 81
NP (Maximum Packet Payload Bytes) 81
RF interfacing commands 82
PL (TX Power Level) 82
PM (Power Mode) 83
CA (CCA Threshold) 83
Sleep commands 83
SM (Sleep Mode) 84
ST (Time before Sleep) 84
SP (Cyclic Sleep Period) 84
DP (Disassociated Cyclic Sleep Period) 85
SO (Sleep Options) 85
Serial interfacing commands 85