User's Guide
Table Of Contents
- XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
- Technical specifications
- Hardware
- Configure the XBee/XBee-PRO S2C 802.15.4 RF Module
- Modes
- Operation
- AT commands
- Special commands
- Networking and security commands
- C8 (802.15.4 Compatibility)
- CH (Operating Channel)
- ID (Network ID)
- DH (Destination Address High)
- DL (Destination Address Low)
- MY (Source Address)
- SH (Serial Number High)
- SL (Serial Number Low)
- MM (MAC Mode)
- RR (XBee Retries)
- RN (Random Delay Slots)
- ND (Network Discovery)
- NT (Node Discover Timeout)
- NO (Node Discovery Options)
- DN (Discover Node)
- CE (Coordinator Enable)
- SC (Scan Channels)
- SD (Scan Duration)
- A1 (End Device Association)
- A2 (Coordinator Association)
- AI (Association Indication)
- DA (Force Disassociation)
- FP (Force Poll)
- AS (Active Scan)
- ED (Energy Detect)
- EE (Encryption Enable)
- KY (AES Encryption Key)
- NI (Node Identifier)
- NP (Maximum Packet Payload Bytes)
- RF interfacing commands
- Sleep commands
- Serial interfacing commands
- I/O settings commands
- D0 (DIO0/AD0)
- D1 (DIO1/AD1)
- D2 (DIO2/AD2)
- D3 (DIO3/AD3)
- D4 (DIO4)
- D5 (DIO5/ASSOCIATED_INDICATOR)
- D8 (DIO8/SLEEP_REQUEST)
- P0 (RSSI/PWM0 Configuration)
- P1 (PWM1 Configuration)
- P2 (SPI_MISO)
- M0 (PWM0 Duty Cycle)
- M1 (PWM1 Duty Cycle)
- P5 (SPI_MISO)
- P6 (SPI_MOSI Configuration)
- P7 (SPI_SSEL )
- P8 (SPI_SCLK)
- P9 (SPI_ATTN)
- PR (Pull-up/Down Resistor Enable)
- PD (Pull Up/Down Direction)
- IU (I/O Output Enable)
- IT (Samples before TX)
- IS (Force Sample)
- IO (Digital Output Level)
- IC (DIO Change Detect)
- IR (Sample Rate)
- RP (RSSI PWM Timer)
- I/O line passing commands
- Diagnostic commands
- Command mode options
- Operate in API mode
- API mode overview
- API frame specifications
- Escaped characters in API frames
- Frame descriptions
- TX Request: 64-bit address frame - 0x00
- TX Request: 16-bit address - 0x01
- AT Command frame - 0x08
- AT Command - Queue Parameter Value frame - 0x09
- Remote AT Command Request frame - 0x17
- RX Packet: 64-bit Address frame - 0x80
- Receive Packet: 16-bit address frame - 0x81
- RX (Receive) Packet: 64-bit address IO frame- 0x82
- RX Packet: 16-bit address I/O frame - 0x83
- AT Command Response frame - 0x88
- TX Status frame - 0x89
- Modem Status frame - 0x8A
- Remote Command Response frame - 0x97
- Regulatory information
- Load 802.15.4 firmware on ZB devices
- Migrate from XBee through-hole to surface-mount devices
- PCB design and manufacturing
Technical specifications General specifications
XBee/XBee-PRO S2C 802.15.4 RF Module User Guide
14
General specifications
The following table describes the general specifications for the devices.
Specification XBee XBee-PRO
Operating
frequency
ISM 2.4 GHz
Supported
channels
11 - 26 12 - 23
Form factor
TH: 2.438 x 2.761 cm (0.960 x 1.087 in)
SMT: 2.199 x 3.4 x 0.305 cm (0.866 x
1.33 x 0.120 in)
TH: 2.438 x 3.294 cm (0.960 x 1.297 in)
SMT: 2.199 x 3.4 x 0.305 cm (0.866 x
1.33 x 0.120 in)
Operating
temperature
-40 to 85 ºC (industrial)
Antenna options
TH: PCB antenna, U.FL connector, RPSMA connector, or integrated wire
SMT: RF pad, PCB antenna, or U.FL connector
Regulatory conformity summary
This table describes the agency approvals for the devices.
Country
XBee
(surface-mount)
XBee-
PRO
(surface-
mount)
XBee
(through-
hole)
XBee-PRO
(through-
hole)
United States (FCC Part 15.247)
FCC ID:
MCQ-XBS2C
FCC ID:
MCQ-
PS2CSM
FCC ID:
MCQ-S2CTH
FCC ID:
MCQ-PS2CTH
Innovation, Science and Economic
Development Canada (ISED)
IC:
1846A-XBS2C
IC:
1846A-
PS2CSM
IC:
1846A-S2CTH
IC:
1846A-
PS2CTH
FCC/IC test transmit power
output range
-26 to +8dBm -0.7 to
+19.4
dBm
-26 to +8 dBm +1 to +19
dBm
Europe (CE) Yes - Yes -
Australia RCM RCM RCM RCM
Japan R201WW10215369 R210- 105563
South Korea MSIP-CRM-DIG-
XBee-S2C
MSIP-CRM-
DIG-XBee-S2C-
TH
RoHS Compliant