Owner’s Guide
Congratulations on purchasing your Wayl Bean X earbuds! Bean X is a powerful, long-lasting true wireless Bluetooth 5.0 earbuds with rich HiFi sound and deep bass. The ergonomic design provides comfort and a secure fit to use for all of your activities. This guide contains instructions for setting up and using your Bean X earbuds. Please refer to the safety instructions for important product safety information prior to use of the product. A PDF version of this guide is available at www.wayl.
table of contents 5 what’s in the box 6 safety instructions 8 bluetooth connect 11 bluetooth connect - computer 12 wear 14 controls 17 talk 18 charging 22 portable charging case 23 care 24 performance 26 labels 28 specifications 30 help 4
what’s in the box 5 1 2 Wireless Earbuds (L/R) 2 Silicone Ear Loops (on earbuds) 2 Silicone Ear Tips (on earbuds) Owner’s Guide 1 Owner’s Guide 1 Portable Charging Case 1 Micro USB Charging Cable
safety instructions Using Your Earbuds Do not turn the volume up too high or to the max level for prolonged periods of time to avoid ear damage. Using the earbuds in both ears while driving is not recommended and can affect your driving. You should use caution or temporarily discontinue use in potentially hazardous situations. Avoid Damaging Your Bean X Do not expose your earbuds or the charging case to excessive heat. Do not drop your earbuds or the charging case; they are not shock-proof.
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives especially on the charging connectors. Use a soft cloth to clean your earbuds; dampened with a minimum amount of water or diluted mild soap. You can also use a pin-like tool to clean hard to reach places in the earbuds. Do not open/replace the batteries in your earbuds or charging case. Operate or store in a place where the temperature is between -15ºC (5ºF) and 55ºC (131ºF) (up to 90% relative humidity).
bluetooth connect First Time Connection Note: Your earbuds come partially charged. Charge your case with the (included micro USB cable) with the earbuds inside for 20 minutes then follow the next steps: Automatic Pairing: 1. Open the charging case and remove both earbuds. They will auto turn-on and announce “power on”. You will see flickering blue lights on both earbuds.
2. The left and right earbud will auto-pair with each other. The earbuds will announce “Pairing” after 3 seconds with both earbuds being out of the charging case. “Pairing” 3. Ready to pair with your device. After 3 seconds, the left earbuds indicator lights will be flashing red-blue which means it’s ready to connect with your Bluetooth device. Step 4: If you are connecting to a computer, please see page 11. 4. Check your device’s Bluetooth Settings.
Manual Pairing: If both earbuds have been out of the charging case (and are off), turn them on by holding down the yellow control button on both earbuds for 3 seconds. You will see a blue light indicator turn on for both earbuds for a few seconds as they auto pair. Follow steps 3 and 4 from Automatic Pairing (previous page) to continue.
bluetooth connect - computer 11 Notes: You must be within 20 (clear) meters of your device. Be sure you disconnect from any previous device and if necessary “forget device” to make sure you can make a new connection to a new device. Computer Settings When you want to connect to a Mac or PC, please reset your earbuds (see page 10). You may need to connect and disconnect a few times in order to address any playback or connection issues. Follow these steps: 1.
wear 12 Earbuds Bean X is designed to provide a comfortable and secure ergonomic fit. The design lets you perform activities without worrying about the earbuds feeling loose or falling out. Look at the labeling on the back of the earbud for which ear it goes to and follow these steps: On the back of the earbud: 1. Fit the silicone ear tip into your ear-hole and push inwards L Left R Right 2.
The earbuds consist of two separable silicone pieces (ear tip and ear loop) to allow for varying use and ease of cleaning (see page 23). To reassemble, attach the ear loop with its earbud (see the letters on the pieces). The letters on the back of the earbud and the ear loop should line up diagonally around a 25° angle when the earbuds are vertical. The ear tip can go with any earbud.
controls 14 Earbuds a Press the a yellow control button to control the earbud as listed below: Action Earbud Result Long Press (3 seconds)* Left or Right Power On / Power Off Long Press (12 seconds)** Both Reset Earbuds One Click Left or Right Cancel Pair Mode Auto Off Both 5 Minutes of Inactivity Auto On Left or Right Remove From Case Auto Pair Left or Right Remove Both From Case Setup * Earbuds will auto turn on when removed from the charging case.
Action Earbud Result Playing Music/Audio (Earbuds must be on)*** One Click Left or Right Play / Pause (Track) Two Clicks Left Skip to Previous (Track) Two Clicks Right Skip to Next (Track) Three Clicks Left or Right Siri or Google Assistant One Click Left or Right Answer Incoming Call Long Press (2 seconds) Left or Right Reject Incoming Call Long Press (2 seconds) Left or Right End Current Call Talk/Calls (Earbuds must be on)*** *** The volume level is controlled by your device
The earbuds volume can only be adjusted by the Bluetooth device it’s connected to or through Siri/Google. For example, on an iPhone when you activate Siri you can say “volume up” to increase the volume a level. For the earbuds indicator lights status, please see page 19.
talk 17 Built-In Microphone Both earbuds have a built-in microphone. You can adjust the volume of your phone (or Bluetooth device) to increase the hearing volume level in your earbuds but you cannot increase the microphone level. The earbuds microphone volume are preset.
charging 18 Charging The Earbuds Place the earbuds firmly into the charging case so that their indicator lights turn on (solid red or blue). Once the earbuds are fully charged their indicator lights will turn blue and auto power off (the charging case will auto power off as well). a b c Earbud Indicator Lights Still Off? Make sure your earbuds and the ear loops are pushed down ( ) firmly in the case and your charging case has power (push the c power button).
a Earbud Indicator Lights (L/R) Red Solid = Charging Blue Solid = Fully Charged The earbuds and charging case will auto power off to save battery life once blue. Red/Blue Blink = Pairing A red-blue blink means the earbud is in pairing mode and will not be charging. To cancel the pair mode: Turn off the case then back on OR Remove both earbuds from the case then place them back in. It will take around 1.5 hours to fully charge the earbuds.
4 Blue Solid = 75-100% power 2 Blue Solid = 25-50% power 3 Blue Solid = 50-75% power 1 Blue Solid = 0-25% power When the charging case nears 0% it will blink Blinking = Charging When the charging case itself is being charged, the current power indicator status will blink. When it’s fully charged while plugged in, you will get 4 blue solid lights. Rotate the case a bit if you have trouble reading which indicator lights are on to get a better angle on the lights glow.
When the charging case is charging, the case will have the current blue indicator status light blinking. Once it is fully charged, you will have four solid blue indicator lights. It takes around 2 hours to fully charge the charging case. If you unplug the Micro USB cable from the charging case while the earbuds are fully charged, the case will auto shut off. To turn on, press the power button on the case. To turn off, press the power button twice.
portable charging case 22 Keep the charging case with you when using your earbuds in case you need to recharge them or experience any technical issues with playback or device connections. In addition to charging your earbuds, you should always place the earbuds back in the case when not in use. When you want to connect to a new device or reset your earbuds, placing them back into the charging case and then removing them will help refresh the earbuds so they are ready for a new connection.
care 23 Cleaning Your Earbuds Separate your a ear tips and b ear loops from your earbuds for faster and better cleaning. You can safely clean the silicone ear tips and ear loops with water and (dish) soap; be sure to dry them before placing them back on the earbuds.
performance 24 Bean X delivers a long-lasting, rich high-quality HiFi sound with deep bass. The higher the volume the better the sound performance. It’s recommended to play the volume level between 60-80%. Do not play at a max volume in order to avoid ear damage. Each earbud has its own large capacity 70mAh li-ion rechargeable battery. The charging case has a large capacity 800mAh Li-ion rechargeable battery.
Standby Time: Several Months When your earbuds are powered off, they can maintain some power for up to 2 months or longer. As long as they are off they will reserve power for an extended period of time. The earbuds will auto power off after 5 minutes of inactivity. Charging Case Charging Time: 2 hours The charging case can be fully charged in 2 hours. The source of charging (vehicle, computer or wall outlet) will have an impact on how fast the case can be charged.
labels 26 f 1c e g a d b h i Wireless Earbuds 70mAh Li-ion Battery (each) a Earbud Body b Earbud Ear Position (L or R) c Silicone Ear Loop (Removable) d Silicone Ear Loop Ear Position (L or R) e Silicone Ear Tip (Removable) f Yellow Power Control Button g Power Indicator Lights h Earbud Mesh i Charge Contacts (For Charging Case)
b g e h h c f a d Portable Charging Case 800mAh Li-ion Battery a Case Body b Case Lid c Power Button d Earbud Position (L or R) e Earbud Placement f Micro USB Charge Port g Power Indicator Lights h Charge Contacts (For Earbuds)
specifications 28 BT Version / Working Distance Version 5.0 / 20 Meters Driver type / Frequency Response / Impedance Dynamic 10mm -20 kHz / 32Ω Earbud Playtime Up to 8 Hours Per Charge Charging Case Earbud Recharges 3 times - 32 Hours Total Playtime Earbuds Battery Type Lithium-Ion Polymer (3.7V, 70mAh Each) Charging Case Battery Type Lithium-Ion Polymer (3.7V, 800mAh) Charging Time for Earbuds / Case 1.
FCC IC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
help 30 Wayl has an extensive knowledge base online to help you troubleshoot any of your Bean X issues. You can reach us online or by email at: www.wayl.shop sales@wayl.shop Quick answers to common issues: I’m having pairing issues. If you’re pairing your earbuds with each other, connecting to your Bluetooth device or are stuck in pair mode (flashing red/blue light indicators), then resetting the earbuds will fix the issue.
loop is in your ear (see page 12, Step 3). If you still can’t get a good fit, it could be that the earbuds are still too large for your ears. Please contact us for further assistance. One earbud does not work when receiving or making a call. Both earbuds should work during a call. If only one earbud is working during or after receiving a call then the other earbud would have to be re-paired with the working earbud. Sometimes a Bluetooth device may interfere with the earbud pair and disconnect one.
Can I use just one earbud? You can use just the left or right earbud. Remove the earbud you want to use and pair it with your device. If you’ve already connected to your device, you will see “Wayl Bean X” in your Bluetooth settings. If you see a new “Wayl Bean X” ready to connect, this would be the other earbud not yet paired. You will see that earbud that is out of the case flashing red-blue lights which means it’s ready to connect to your device.
The right earbud is not turning on. If the right earbud is not on (but the left one is) and you can only hear audio in the left earbud, it can be due to several issues. a) check to see if the battery is dead. Place the right earbud back into the charging case along with the left earbud and wait 10 minutes. Remove both earbuds from the case. It should auto pair with the left earbud (if you see red-blue flashing on the right earbud, press the yellow control button).
