User manual

Mute Function
Setting up your BEAM RST310 IntelliDOCK Remote Satellite Docking Station
8
2
7
5
!!
CAUTION:
DO NOT connect LIVE power to the unit until
the installation is complete.
Connect the AC/DC Power
With LIVE power turned OFF, connect power jack to rear of RST310.
Secure cable by tightening collar
Connecting an RJ11 telephone handset (optional)
Connect a telephone handset, answering machine or cordless phone into
the Line or Accessory socket. This socket supports a standard RJ11 plug.
Connecting your SatDOCK
To connect your SatDOCK to the IntelliDOCK, follow the below steps.
3
Facsimile Messaging via a standard RJ11 connection is not supported on the
Iridium Network see your Service Provider to discuss the dedicated FX2600
Iridium Fax Adapter or visit us at www.beamcommunications.com
Connecting an Intelligent handset (optional)
Connect to the Iridium Intelligent Handset, if supplied, directly to the Handset socket of
the RST310.
Only use the extension cables for this handset provided.
Cables up to 30 metres in length are available from your Service Provider.
Rear of RST310
SatDOCK Power LOG port
Handset Line iHandset COMM port
4
Suppl
ied
w t
i
h
5
Ha
n
d
et
9
05A
s
Antenna Cable
Powering Up & Making/Receiving calls
When all previous 1-6 steps have been completed, confirm that the antenna is connected and the
power loom active.
Ensure that the 9505A handset is powered off and seated in the SatDOCK cradle.
The handset will power on automatically once power is connected to the RST310.
Once power is connected, allow up to 3 mins for the LEDs to register with network.
To successfully make a call on the Iridium network, you need:
1) Dial tone on the telephone handset
2) Call LED must shine or continuously.
Continue to make your phone call as you normally use a traditional phone, noting any dialling prefix instructions
advised by your service provider.
Once you have entered the phone number you will hear progress pips from the Iridium network. It can take up to 30
seconds for the Iridium network to connect a call, so a pause at this stage is not unusual.
You will shortly hear the called party end ringing, or hear a busy tone and voice message indicating why your call was
not possible. When the other party answers the Call LED will change from steady to flashing
indicating 'call in progress'. This is a normal operating procedure.
To end the call, hang up the handset. The Call LED light will then turn off.
green orange
orange orange,
6
Installing your External Iridium Antenna
See the specific “Iridium Antenna Installation Guide” manual or visit us @ www.beamcommunications.com
Connecting your Laptop/PC
Plug the serial cable into the Comm Port of the RST310.
For more information on how to configure and access data services, please
refer to the Beam Data Guide.
For information on Iridium’s Data Services, please visit www.iridium.com
t
e n
To
A
n
n
a
A.
B.
C.
D.
Locate the supplied SMA / TNC Antenna Adapter.
Fasten the Antenna Adapter to the Antenna cable.
Connect the Antenna cable to the
SMA socket on the rear of the
SatDOCK Cradle and screw to
tighten.
E.
Connect the SatDOCK interface
cable to theinterface port on the
rear of the SatDOCK Cradle
and tighten both thumb screws.
Connect the other end of the interface cable to
the Interface port on the rear of the IntelliDOCK.
Tighten both screws to secure.
Docking / Undocking your 9505A handset
To dock the 9505A handset, firstly ensure you remove the rotating antenna from the handset. Place the
base of the 9505A handset into the seat of the SatDOCK ensuring that the pins on the bottom of the
9505A handset line up with that on the seat of the SatDOCK cradle as illustrated below.
Push down on the handset to seat the handset base firmly in the SatDOCK cradle.
To clip the handset into place, press and hold the button on top of the 9505A handset whilst pushing it
back into the SatDOCK until it clips into place. Release the button on top. Gently pull on the handset to
confirm that it is docked correctly and won’t come loose.
When removing 9505A Handset from the SatDOCK cradle, reverse the above steps, ensuring you hold
down the button on top of the handset before trying to remove it from the SatDOCK.
The handset can now be powered on for normal mobile operation - refer to 9505A manual for further
information.
Stage 3
Stage 1
Stage 4
Stage 5
Stage 2
Antenna Operation
Please note that earlier firmware versions of the 9505A handset may display a message prompting the user to
rotate the antenna. To toggle between enabling / disabling this Antenna Alert when in the SatDOCK, using the
keypad on your 9505A handset, type in the following code : *#92#
!!
9
Mute Functionality
To mute all audio to the handset whilst docked to the SatDOCK cradle, simply press
the mute button once. A red light will illuminate on the mute button to visually confirm
that the SatDOCK is muted.
To un-mute, simply press the mute button again, and the mute light will extinguish.