User manual

S
2U
S
R
Q
G
00
160
RST310
IntelliDOCK
Quick
Start
Guide
Beam Communications Pty Ltd
8 Anzed Court, Mulgrave
Victoria, Australia, 3170
T: [phone]
F: [phone]
E: [e-mail]
W: www.beamcommunications.com
RST310 options include:
Iridium is a line-of-sight Satellite network, conditions that can
compromise the quality of the service you may receive include:
Optimising Iridium performance
More info @
www.beamcommunications.com
1. Obstructions: Provide the best satellite view for your antenna by removing all obstructions where possible
2. Cabling: Use the shortest cable length and the fewest number of connectors on all Iridium certified antenna cable runs
3. RF Interference: Install antenna as far away from other transmitters as possible.
1 x RST310 unit
1 x universal plug-pack power adapter, 110-240V AC
1 x 9-pin-to-9-pin RS-232 cable (Male to Female)
1 x Printed user manual
1 x SatDOCK Cradle
1 x SatDOCK Interface Cable
1 x RAM Bracket / 2 x M4 Screws
2 x Mounting Brackets
1 x Mounting Screws (packet)
1 x “Installing Iridium Antennas” Guide
1 x Beam Starter CD
Package Contents
Before commencing installation ensure your package
has the following components:
1. Mounting your RST310
2. Connect AC / DC Power
3. Connecting your SatDOCK
4. Docking / Undocking your 9505A handset
5. Connecting an RJ11 telephone handset
6. Installing your external Iridium antenna
7. Connecting your Laptop / PC
8. Powering Up & Making / Receive calls
9. Mute Function
Thank you for purchasing the BEAM RST310
his QuickStart Guide install
your
T lists the steps to
BEAM Satellite equipment:
1
Your handset cradle mounting options:
1) Separate: Carefully slot the RST310 between the two mounting brackets and
secure with the retaining screws. Mount the Ram-mount cradle for the 9505A in
the desired location ensuring that there is sufficient cable length for the handset to
connect to the main terminal.
2) Together: Using the brackets supplied the Ram-mount handset holder can be firmly attached to the
terminal as pictured below, follow the above instructions for mounting the terminal, however using the longer
mounting screws supplied affix the additional ram-mount holding bracket to the side of the unit.
Mounting your RST310
The RST310 comes with two (2) right angle brackets that allow mounting for mobile and fixed positioning.
Carefully slide the RST310 between the two mounting brackets and secure with the retaining screws.
A: Drop-in mount
Note: To ensure a secure installation:
1. Mount the RST310 on a clean, even surface.
2. Clean the mount surface of the RST310.
3. Use the correct type of screws (as supplied)
4. If mounting on wood, ensure wood is structurally sound.
5. Leave enough room around the RST310 to allow easy
access to the rear panel.
Do not install the unit in a permanently concealed area.
Access must be possible in the event of future service.
B: Flush mount
1. 2. 3. 4.
1 & 2: Connect bracket to RST310 3 & 4: Secure RAM-mount on top of unit.
LEDs
PIN Code
To make and receive calls, you may need to enter a PIN code.
RST310 Signal LED Handset tone Action required
Flashing Red LED

Distinctive
dial tone:
two tones of
equal length
Enter four digit SIM PIN and await a
change of tone (up to 10 seconds),
then hang up.
When successful the phone will register
and proceed with normal use
Flashing Red LED

Distinctive
dial tone:
high tone is
longer than
low tone
Enter the PUK code, await a change of
tone (up to ten seconds) and hang up.
When successful the phone will register
and proceed with normal use
Constant LED Normal dial tone No action required
910 Iridium Helix
POTS Handset
Intelligent Handset
Fax Adapter
Power LED: flashes during self-diagnosis then illuminates a steady .
Vmail/SMS LEDs: flashes to indicate message(s) are waiting in your
voice mailbox to be retrieved.
* This service is subject to network support and not available from all providers.
Call LED: Varies with status of call, which can be:
“In Call”, “Waiting to connect”, or “Incoming call”
Signal LED: indicates strength of Iridium signal at your location.
= no signal/PIN code required
= low signal
= Good signal
green
GREEN
RED
ORANGE
Front of RST310
R
0
ST3
1
Charge LED
Mute LED
State
Handset is fully charged
Handset is charging
Handset absent
Mute Mode
Privacy Mode
Incompatible handset /
Connection Error
(Solid)
(Flashing - Slow)
(Solid)
(Solid)
(Flashing - Fast)
Normal Handsfree Mode
(Off)
(Flashing - Slow)
Charging Error
* (Solid)
*Eg. Unsafe ambient temperature for charging
(Off)
S
a C
tDO K
Front of SatDOCK
If any problems, try the following:
1. Repeat these instructions to ensure everything has been
completed.
2. Is there power to the unit? Check all connections and fuses.
3. Is the SIM card active? If not, refer to your Service Provider
4. If the antenna signal is not strong try moving antenna
location to achieve better coverage/signal and re-test.
For additional troubleshooting refer to your manual or visit us:
www.beamcommunications.com