Owner Manual

L’installation est simple comme bonjour!
Préparation du piédestal
a.
Pour installer
efficacement les potelets
à montage sur colonne, utiliser le
gabarit de montage sur colonne
qui accompagne ce guide
d’installation.
b.
Poser le gabarit sur la colonne
désirée et marquer
l’emplacement des trous de
montage (voir le gabarit inclus).
c.
Percer des trous de montage de
3,8 cm (1 1/2 po) de profondeur
à l’aide d’un foret béton de 5/16
po (pour pose sur les surfaces
en briques ou en béton) en
maintenant le conduit
électrique centré entre les deux
trous. Le conduit électrique doit
avoir une hauteur libre de 7,5
cm (3 po). Pour une installation
sur des colonnes en bois, utiliser
des vis à bois de 1 1/2 po.
d.
Pour une installation sur les
briques ou le béton, enfoncer
des chevilles en plastique
complètement dans les trous
percés (voir la Figure A).
Figure A
Instructions de montage
des potelets
extérieurs sur piédestal
Conduit
électrique
Chevilles
en plastique
ColonneGuide pour
piédestal
Trous de
5/16 po
Couper le courant
Toujours couper le courant au tableau électrique ou débrancher le fusible
lors de l’installation ou de la réparation de tout autre appareil électrique.
LA PRÉSENCE
DE COURANT
PEUT CAUSER
DES
BLESSURES
GRAVES, VOIRE
MORTELLES
ATTENTION
–Outillage nécessaire–
• Tournevis Cruciforme
• Mastic
• Ampoules
• Foret de
5
/
16 po pour
colonnes en béton
ou ou
Caulk
Assemblage
Le temps de montage est de 35 minutes environ
Guide
E
18W/840
ou
IMPORTANT! PLEASE READ:
All solid brass and cast aluminum lanterns are prepared
with a durable lacquer finish or a powder-coated/painted finish.
Please note that the brass finish or painted finish on exterior lantern
s will
weather or tarnish over time, depending upon the environmental conditions where the lantern is installed.
Your proper care of lanterns (see below) will enhance both the life and appearance of the lanterns. Post treatments,
such as clear lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of a brass lantern, it is important that dust and debris is removed from the
surface of the lantern periodically. It is recommended that the lanterns be wiped down weekly using a soft, dry or
damp cloth.
DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass cleaners or chemicals, as this
will scratch/remove/damage the protective coating, allowing moisture and pollutants to come in contact with the
brass, which will result in discoloration and pitting.
ALL cast aluminum lanterns receive a durable powder coat finish, which enhances the durability of the lantern.
This finish should also be wiped down weekly with a soft, dry or damp cloth to remove the dust and debris that
will accumulate on the surface. DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass
cleaners or chemicals as this may damage the finish.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL VOID THE WARRANTY OF THE
LANTERN.
LIMITED WARRANTY
W
arrants against defects in materials or workmanship for a minimum of TWO (2) YEARS from date of purchase
for use, and agrees to repair or, at our option, replace a defective unit without charge. Brass finish is
covered 90
days from purchase date.
IMPORTANT: This Warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable
care (see above), the affixing of any attachment not provided with the product, alteration of any attachments
factory installed, loss of parts or subjecting the fixture to any but the specified electrical service. This warranty
does not cover failure of bulbs due to accidents, abuse, misuse, vandalism, power surges, and acts of nature such
as lightning damage or any bulbs purchased separately and installed by the consumer or any damage to the fixture
caused by a separately purchased bulb.
No responsibility is assumed for any special incidental or consequential damages. Damages occurring during
transit are not covered by this warranty.
f.
For screw on glass fixtures, unscrew glass counter
clock wise. Insert bulb(s) and screw glass back on
(see figure 7).
g.
Turn power on.
Figure 7
Screw on Top Glass Assembly
Glass
Twists
Off
If fixture does not work:
1. Turn off electrical power and check all wire connections.
2. Check fuse or circuit breaker and replace if necessary.
3. Check to make sure light bulb is in working order.
4. Ensure that dimmer switch is in the "on" position.
Troubleshooting
E4
F1