Assembly And Installation Instructions

ManualsBrandsBeachcrest Home ManualsLightingArchibald Dualux© Outdoor Barn Light with Motion Sensor

Page 1/4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

Features

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

Mounting Screw (B)

Green Grounding

Screw (C)

Lock Nut (F)

Wire Nut (E)

Ball Nut (G)

Rubber Pad (H)

Cross Bar (A)

Headless

Screw (D)

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

replacing the bulb.

8. Compatible with LED dimmable bulb.

Maximum Wattage: 60W Incandescent Bulb or 20W LED

dimmable bulb.

Work Temperature: -4°F~104°F

Hardware Package (included):

Ball Nut (G)

Rubber Pad (H)

Fixture

Glass Shade

Small Ball nut

Rubber pad

Metal frame

Fixture Wire

Wire Nut (E)

Fixture Grounding Wire

Headless Screw (D)

Cross Bar (A)

Lock Nut (F)

Outlet Box

House Grounding Wire

Green Grounding Screw (C)

Mounting Screw (B)

Back plate

Type A15,Type B

Type A

Max. 60W: Incandescent/Halogen Bulb or

Max.20W Dimmable LED Bulb

(not include)

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation steps Turn off the power at fuse or circuit box. 1.Thread two headless screws through the cross bar, then screw them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screw if necessary. Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level. 2. Attach the cross bar to the outlet box by using two mounting screws. 3. Pull out the source wires from the outlet box.
PAGE 3
FIG.1 FIG.2 Manual Override Operation Diagram AUTO Mode Turn wall switch OFF-ON in 3 Seconds Turn wall switch OFF-ON in 3 Seconds again On the back of the sensor Low Level Sens Time Manual Override Mode Test 3H 6H 0 CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
PAGE 4
---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1. Make sure there is no movement that could be picked up by the sensor. 2. Adjust the time knob counterclockwise to reduce the delay shut-off time.