User`s guide

ManualsBrandsBEA ManualsComputer equipmentLZR-I100

75.5753.02 LZR-MICROSCAN 20140107 Page 1 of 12

LZR-MICROSCAN

Stand-Alone, Door Mounted, Safety

Sensor for Automatic Swing Doors

(US version)

ENGLISH

DESCRIPTION

1. tilt adjustment 4. end caps 7. adjustment knob

2. sensor connection ports 5. optical window 8. LCD

3. sensor LED 6. plug-n-play ports 9. hub LEDs

INCLUDED KIT COMPONENTS

DESCRIPTION PART NUMBER SINGLE

PAIR/DE

Left LZR-microscan Sensor 10LZRMICROLEFT 1 2

Right LZR-microscan Sensor 10LZRMICRORIGHT 1 2

LZR-microscan Hub 10LZRMICROSCANHUB 1 1

Master Sensor Harness 35.1326 1 2

Slave Sensor Harness 35.1327 1 2

Door Control Harness 20.5222 1 2

System Harness 20.5304 1 1

Eagle Harness 20.5069 1 1

Power Supply Harness 20.5095 1 1

Home Switch (Surface Mount) 50.5283 1 2

Door Loop / Cap Kit 70.0202 / 50.0078 1 2

On / Off / Hold Open Switch Jumper 20.5310 1 1

Left Pass-Through Sensor Endcap 41.7922 1 2

Right Pass-Through Sensor Endcap 41.7923 1 2

Sensor Spacer 70.5554 1 2

Spacer Mount Screws 50.0048 2 4

Sensor Mount Screws (Metal) 50.1818 2 4

Sensor Mount Scews (Wood) 50.5282 2 4

Endcap Screws 41.8632 4 4

Velcro Tabs 50.0046 2 2

LZR-microscan Mounting Template 75.5754 1 1

LZR-microscan User’s Guide 75.5753 1 1

Power Supply 30.5558 1 (Universal

ONLY) 1 (Universal

ONLY)

On / Off / Hold Open Switch 10DOORSWITCH 1 (Universal

ONLY) 1 (Universal

ONLY)

REQUIRED TOOLS

TOOL

Power Drill

Tape Measure

Magnetic Phillips #0

Phillips #2

1/8” Drill Bit

5/16” Drill Bit

3/8” Drill Bit

1/2” Drill Bit

Pencil

Center Punch / Hammer

Wire Nuts

Wire Snips

Wire Fish

MOUNTING KITS

DESCRIPTION PART NUMBER

Narrow Frame Door 10MICROSCANMOUNT

Glass / Fire Door 10MICROSCAN-Y

NOTES:

1: Single Door Kit

(10LZRMICROSCAN1)

2: Pair/Dual Egress Door Kit

(10LZRMICROSCAN2)

3: Universal Single Door Kit

(10LZRMICROSCAN1U) and

Univeral Pair/Dual Egrees Door Kit

(10LZRMICROSCAN2U)

Summary of content (12 pages)

PAGE 1
ENGLISH LZR-MICROSCAN Stand-Alone, Door Mounted, Safety Sensor for Automatic Swing Doors (US version) DESCRIPTION 2 6 1 5 3 8 7 9 4 1. tilt adjustment 2. sensor connection ports 3. sensor LED 4. end caps 5. optical window 6. plug-n-play ports INCLUDED KIT COMPONENTS 7. adjustment knob 8. LCD 9.
PAGE 2
PRECAUTIONS ! • • •  Shut off all power going to header before attempting any wiring procedures.  Maintain a clean & safe environment when working in public areas.  Constantly be aware of pedestrian traffic around the door area.  Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.  ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge.
PAGE 3
IMPORTANT: In order to guarantee proper installation, instructions must be followed in order! Verify operation/functionality of door control and operator prior to system installation. PREPARATION Hub 1 Install hub in door header, centered and in an easily accessible location. 2 Plug System Harness into hub port labeled System. Do not plug in any other harnesses. Sensors 1 Determine on which side of door Door Loop will be installed and cut to shortest length to avoid loop in detection zone.
PAGE 4
INSTALLATION Sensors Refer to mounting template for full mounting instructions! 1 2 LEFT MOUNT DISTANCE FROM TOP OF DOOR sensor mounting 1/8 “ wire passage 5/16 “ microscan * Scan for Product Info 3 MOUNTING INSTRUCTIONS NOTES: Mount sensors as close to top of door and as close to hinge of door as possible. Spacer required for applications with hardware extending across width of door and protruding more than 2 in.
PAGE 5
INSTALLATION (cont.) Periphials All periphial devices, including safety, activation, security, and logic modules should be wired directly to hub and not to door control. On / Off / Hold Open Switch If using an existing on / off / hold open switch, plug On / Off / Hold Open Switch Jumper into hub port labled On / Off / Hold Open and wire nut red and black wires together, or if desired, splice existing switch into Jumper. 1 Determine mounting location, apply mounting template, drill holes.
PAGE 6
INSTALLATION (cont.) Door Control Harness 1 NOTES: 2 If door system utilizes independent door controls, repeat steps 1-2 for the second control. Do not use door control sync cable. Door Control Plug Door Control Harness into hub port labeled Door Control A. For dual egress doors with independent stall, two (2) Door Control Harnesses must be used. Wire Door Control Harness to door control.
PAGE 7
INSTALLATION (cont.) Wiring (cont.
PAGE 8
SETUP CAUTION: No safety will be present during the Teach In and Learn cycles. 1 2 Program hub according to desired settings. Menu 1 (Basic) items MUST be programmed. 4 3 Return to home screen. Push and hold adjustment knob for three (3) seconds, until blue LED begins to flash. 5a Network icon will appear for approximately five (5) seconds. 6 5b “CLEAR AREA” will display and countdown will begin. Clear area around door on both sides. For dual egress doors, Push Door icon will display.
PAGE 9
OVERVIEW OF SETTINGS Menu 3 (DIAGNOSTICS) Menu 2 (ADVANCED) Menu 1 (BASIC) MENU LCD DISPLAY PARAMETERS DoorType Undefined Single Pair DualEgr InDualEgr DESCRIPTION Type of door system on which sensors are installed Single: Single Door DualEgr: Dual Egress Doors Pair: Pair of Doors InDualEgr: Independent Dual Egress Doors DetectZoneA 24 - 48 Distance (in inches) from sensor LED to leading edge of Door A [round down] DetectZoneB 24 - 48 Distance (in inches) from sensor LED to leading edge of D
PAGE 10
HOW TO USE THE LCD DISPLAY DURING NORMAL OPERATION Safety Activation Stall (door 1 & 2) Negative display = active output To adjust contrast, push and turn the grey button simultaneously. Opposite for reverse logic During normal operation only. FACTORY VALUE VS. SAVED VALUE displayed value = factory value displayed value = saved value NAVIGATING IN MENUS Push to enter the LCD-menu Scroll menu items Select your language before entering the first LCD-menu.
PAGE 11
TROUBLESHOOTING Hub LCD is not on No input power Verify power supply connection, do not power from door control Bad power Verify power supply, power from BEA power supply Faulty hub Replace hub No “CLEAR AREA” during setup Sensors not discovered Verfiy sensor harness connection No Floppy Disk after setup Learn failed Perform new learn Door(s) will not open/close Door control issue Verify door control is operational with nothing wired to it No inputs/outputs connected Verify all connections
PAGE 12
©BEA|OriginalInstructions|75.5753.02LZR-MICROSCAN20140107 PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING TECHNICAL SPECIFICATIONS Technology: laser, time-of-flight measurement Detection mode: presence Max. door width: 48” Mounting Height: 6’ 7” - 8’ 2” (for greater heights contact Tech Support) Remission factor: > 2% Angular resolution: 2.56 ° Testbody: 28” (H) x 12” (W) x 8” (D) according to UL325 Emission characteristics: IR laser: wavelength 905 nm; max.