SEQUEL® 20 6151/6152 LIFT DESK INSTRUCTION MANUAL LET’S GET STARTED.
Congratulations on the purchase of your Sequel 20 Lift Desk 6151 / 6152 from BDI. Your desk has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information that will ensure that you get the most out of your desk. Please save it for future reference. Your Sequel 20 Lift Desk is designed for indoor use on level floors. It has been engineered for easy assembly. Please follow these directions carefully to prevent any damage.
HARDWARE AND COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product. For all other concerns, please contact your BDI retailer.
HARDWARE AND COMPONENTS PART # DESCRIPTION PART # C1 DESCRIPTION Keypad C2 Control Module PART # C3 DESCRIPTION Leg QUANTITY 1 QUANTITY 1 QUANTITY 2 PART # C4 PART # C5 PART # C6 DESCRIPTION Foot DESCRIPTION DESCRIPTION QUANTITY PART # DESCRIPTION QUANTITY Cord Extension QUANTITY 1 QUANTITY 2 PART # C7 DESCRIPTION Wire Tray Cord Conduit 1 PART # DESCRIPTION QUANTITY PART # DESCRIPTION QUANTITY 1 C8 QUANTITY 1 Power Cord C10 Grommet Cover 1 C9 Glass Panel TOOL R
ASSEMBLY STEP 1. INSTALL CONTROL MODULE AND KEYPAD Lay (A1) Main Panel upside down on a soft surface (carpet). Attach (C1) Keypad on the desired side (choose left or right) with 2 (H2) Short Wood Screws and a Phillips Screwdriver. IMPORTANT! Orient the (C2) Control Module so that the keypad cord socket (labeled HS) is facing the keypad side and secure between the 2 steel rails with 2 (H1) Long Wood Screws as shown. Route the keypad cord into the groove in the panel and through the hole in the metal frame.
STEP 2. CONNECT & SECURE KEYPAD ASSEMBLY Attach keypad cord into the (C2) Control Module socket (labeled HS) and bundle the slack with the hook and loop tie. Secure the keypad cord into the groove using 6 (H7) Cord Clips and 6 (H2) Short Wood Screw. Tighten with a Phillips Screwdriver.
ASSEMBLY STEP 3. INSTALL LEGS Attach 2 (C3) Legs with 4 (H5) Screws per leg using (T1) Hex Wrench. Start all 4 screws before tightening them down. Connect (C4) Cord Extension into the top of (C2) Control Module. Connect 1 leg cord to the end of (C4) Cord Extension, connect the other leg cord to the other end of the (C2) Control Module and bundle up any slack using the hook and loop ties.
STEP 4. INSTALL FEET ASSEMBLY Attach (C5) Feet with (H4) Flathead Screws and (T1) Hex Wrench. Make sure the longer end of the feet are facing the front of the desk (same side as keypad). PART/DESCRIPTION QTY T1-HEX WRENCH 1 H4-SCREW 8 H4 C5 H4 C5 Long end this side H4 NEED ASSISTANCE? customerservice@bdiusa.com C5 BDIUSA.
ASSEMBLY STEP 5. INSTALL WIRE TRAY—OPTIONAL Determine if you prefer the wire tray to be centered, shifted left or shifted right. If you plan to use a monitor arm, it might be better to shift the position of the (C7) Wire Tray to make the monitor arm attach more centrally. Attach the metal (C7) Wire Tray to the back edge of the bottom of the desk with 2 (H5) Screws. Shifted Right PART/DESCRIPTION QTY H5-SCREW 2 Shifted Left C7 H5 H5 10 | BDIUSA.
STEP 6. ATTACH SURGE PROTECTOR—NOT INCLUDED Secure 4 pairs of (H9) Dual-Lock Dots to the bottom corners of your surge protector. ASSEMBLY PART/DESCRIPTION QTY H9-DUAL LOCK DOT 4 Surge Protector (not included) Attach Dual Lock together ATTACH YOUR SURGE PROTECTOR—NOT INCLUDED Determine where you prefer your surge protector to be mounted. We suggest just behind the metal rails towards the leg closest to your wall outlet. Make sure the area is dust free.
ASSEMBLY STEP 7. INSTALL DRAWER—OPTIONAL Attach the (6159) Optional Drawer (for 6151/6152) using 4 Screws that came with your drawer as shown. 6159 ASSEMBLY STEP 8. PLUG POWER CORD Plug the (C6) Power Cord into the power port on the (C2) Control Module (labeled AC). C2 C6 12 | BDIUSA.
2 PERSON TASK STEP 9. ATTACH DUAL LOCK FASTENER—OPTIONAL ASSEMBLY With the help of another person, carefully pick up, rotate, and place the desk on to its feet. Plug the other end of the Power Cord into the nearest wall socket. Refer to the User Manual on Page 18 and follow the Reset Procedure. You may now adjust the height of your desk to make the remaining steps easier. STEP 10. INSTALL GLASS BUMPERS ASSEMBLY Install the 2 (H8) Glass Bumpers as shown.
2 PERSON TASK ASSEMBLY STEP 11. INSTALL GLASS PANEL & GROMMET COVER With the help of another person, carefully place the (C8) Glass Panel on top of the desk top with the metal pucks facing down. The stem of the glass pucks should slip into 5 holes. Secure the (C8) Glass Panel in place from below using 5 (H6) Screws. Do not over tighten. Open drawer to attach front, center screw. Place (C9) Grommet Cover into the grommet hole. PART/DESCRIPTION QTY H6-SCREW 5 C9 C8 H6 H6 H6 H6 H6 14 | BDIUSA.
STEP 12. ATTACH CORD CONDUIT—OPTIONAL ASSEMBLY Remove adhesive film and attach the (C6) Cord Conduit to the back of the top section of the leg nearest the wall outlet. Insert power cord(s) into (C6) Cord Conduit. C6 C6 C6 NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
ASSEMBLY STEP 13. INSTALL MONITOR ARM—OPTIONAL, NOT INCLUDED The Sequel Lift Desk is compatible with most third party monitor arms. Attach your monitor arm on either side of the grommet hole along the back edge, staying at least 1" away from the grommet hole. The Sequel Lift Desk can support 75lb (34Kg) on a monitor arm. Optional Monitor Arm (not included) 16 | BDIUSA.
WIPE EXCESS LEG LUBRICANT FINE TUNING When new, the legs may have excess lubricant. Extend the legs to their highest position and wipe off excess lubricant with a clean, dry cloth or rag. NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
USER MANUAL CAUTION! n n n Make sure there are no obstacles under or over the path of the desk. Make sure the desk top is not touching any walls. Make sure all the cords are long enough to reach lowest and highest desk positions. ! ! IMPORTANT: YOU MUST RESET THE DESK PRIOR TO USE. RESET PROCEDURE 1. 2. 3. 4. 5. Press and hold the DOWN button on the keypad until the desk reaches its lowest height. Release the DOWN button. Press and hold the DOWN button again until the LED display reads “RST”.
HEIGHT ADJUSTMENT The desk base can be adjusted by pressing and holding either the UP or DOWN button until the desired height is reached. To program up to four presets, use the up/down buttons to find a desired height, then press “BDI” followed by a number 1-4. To Change the Movement Program (explained below) follow the Reset Procedure to Step 4. The display should be flashing “RST”. Press and hold the “1” button (about 5 seconds) until the display flashes “10.1” or “10.2”.
SETTING THE UPPER AND LOWER LIMITS The base is designed to go to its minimum and maximum heights, allowing for the widest possible range. If you prefer to change the settings to a more narrow range, follow these steps: TO SET THE LOWER-LIMIT POSITION Use the UP/DOWN buttons to move the base to the desired minimum height position. Press and release the “BDI” button and the LED display should read “S”. Next, press and release the DOWN button.
TROUBLE SHOOTING If your desk is not functioning properly it may need to be reset. Follow the RESET procedure above. If your LED readout displays an error message Er1 confirm that all wired connections are secure. Then perform the reset procedure above. Check that all cables and the power cord are correctly plugged in. Is the desk now working properly? YES NO Does the display read “HO1”? NO YES Does the display read “RST”? YES YES Follow the system reset procedure.
CARE & MAINTENANCE GLASS Glass surface is maintained using household glass cleaner and a paper towel or cloth. SATIN-ETCHED GLASS This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available at any grocery store or home improvement center.
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. The decision to repair or replace will be at BDI’s sole discretion.
These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.05.28.2020 Made in Vietnam.
