SEQUEL® 20 6117 MULTIFUNCTION CABINET INSTRUCTION MANUAL LET’S GET STARTED.
Congratulations on the purchase of your Sequel 20 Multifunction Cabinet 6117 from BDI. Your file cabinet has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information that will ensure that you get the most out of your cabinet. Please save it for future reference. Your Sequel 20 Multifunction cabinet has been engineered for simple assembly. Please follow these directions carefully to prevent any damage.
HARDWARE HARDWAREAND ANDCOMPONENTS COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product. For all other concerns, please contact your BDI retailer.
HARDWARE AND COMPONENTS PART # DESCRIPTION C1 Cabinet PART # C2 DESCRIPTION Leg QUANTITY 2 PART # C3 DESCRIPTION Drawer Pull QUANTITY 1 QUANTITY 3 PART # C4 PART # C5 DESCRIPTION QUANTITY Adjustable Shelf 1 DESCRIPTION QUANTITY Glass Top Panel 1 TOOL REQUIRED (NOT INCLUDED) Phillips Screwdriver NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
2 PERSON TASK ASSEMBLY STEP 1. ATTACH THE LEGS Make sure (C4) Adjustable Shelf is still held in place with packing material (or removed from the (C1) Cabinet). Carefully position (C1) Cabinet onto its back. Install (C2) Leg Frames using (H1) Screws and (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 16 Brace or Remove (C4) Adjustable Shelf C4 H1 C1 C2 H1 C2 H1 H1 C2 H1 6 | BDIUSA.
2 PERSON TASK STEP 2. PLACE GLASS TOP ASSEMBLY With help from another person, carefully lift the cabinet onto its base. Place (C5) Glass Top Panel into position on top of the (C1) Cabinet. Align all edges. The glass edge should be offset 1.5mm from the side of the cabinet on all 4 sides. C5 1.5 mm C1 STEP 3. ATTACH DRAWER PULLS ASSEMBLY Open a drawer and connect a (C3) Drawer Pull using 2 (H2) Screws. Tighten with a Phillips Screwdriver (not included).
FINE TUNING ADJUSTABLE SHELF Install the (C4) Adjustable Shelf. You may adjust the position of the (C4) Adjustable Shelf by pulling the 4 shelf pins out and relocating them. PART/DESCRIPTION QTY T2-Leveler Wrench 1 LEVEL CABINET Make sure the (C1) Cabinet is level. Adjust 1 or more of the levelers using (T2) Leveler Wrench to attain a level stance. C4 Shelf pins C1 T2 Dial down 8 | BDIUSA.
FINE TUNING ARRANGING YOUR FILES For forward facing files, attach (H6) File Bar Clips to each end of the (H4) Small File Bars. Slide the bars onto the rails so that the (H6) File Bar Clip goes into the groove. PART/DESCRIPTION QTY H4-SMALL FILE BAR 2 H5-LARGE FILE BAR 1 H6-FILE BAR CLIP 6 For sideways facing files, see below. H4 H6 H6 H6 Legal H4 Letter/A4 H6 Grooves H4 H6 For letter files facing sideways, attach (H6) File Bar Clip to both ends of (H5) Large File Bar as shown.
CARE & MAINTENANCE GLASS Glass surface is maintained using household glass cleaner and a paper towel or cloth. SATIN-ETCHED GLASS This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available at any grocery store or home improvement center.
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. The decision to repair or replace will be at BDI’s sole discretion.
These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.06.09.2020 Made in Vietnam.
