SySTIUM TECHNOLOGIES ® Assembly Guide Model 526
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 526 Radio Frequency Interference Notice (USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MotherBoard ReadySM System • MODEL 526 SySTIUM® TECHNOLOGIES ASSEMBLY GUIDE Assembly Safety Instructions Before You Begin Assembly of a computer system using this product shall be assembled only by technically qualified personnel. Follow the instructions in the document “Model 526 Maintaining Regulatory Compliance” to meet and maintain the safety and product regulatory compliance of this product when assembling a computer system using this product. 1.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 526 BULK PACKAGE Removing the 5.25” Peripheral Carrier Please re-cycle the packaging. None of the bulk pack packaging is designed for reuse when shipping to the end customer. NOTE: CONTENTS The Model 526 MotherBoard Ready System product contains the following: • • • • Model 526 Chassis with Power Supply Installed North American Compliant Power Cord Integration Kit Quickstart Guide. (This manual must be included in shipment to the End User.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 526 Installing the I/O Shield (Intel BOX Motherboard) 1. Locate the motherboard I/O shield supplied with the Intel BOX motherboard. 2. Place the lower surface of the I/O shield in the I/O opening in the rear of the chassis. Ensure the I/O shield is fully inserted into the opening. Refer to Figure 5 3. Carefully press the top surface of the I/O shield into the I/O opening.
MotherBoard ReadySM System • MODEL 526 SySTIUM® TECHNOLOGIES Installing a 3.5” External Peripheral (Floppy) FIGURE 7 1. 2. 3. 4. Removing the Bezel Filler Panels 1. To remove the peripheral filler panels push the mounting tabs toward each other to release the panel from the bezel. See Figure 8 If the 3.5” carrier is not already removed you must remove it. To remove the 3.5” carrier following the instructions in the section “Removing the 3.5”Peripheral Carrier”.
MotherBoard ReadySM System • MODEL 526 SySTIUM® TECHNOLOGIES Installing a 5.25” External Peripheral FIGURE 13 NOTE The system must have one 5.25" external peripheral installed or an EMI shield must be installed. Failure to install a 5.25" external peripheral or EMI shield can result in EMI leakage that will result in the computer system not meeting the product's EMC compliance. 1. 2. 3. If the 5.25” carrier is not already removed you must remove it. To remove the 5.
MotherBoard ReadySM System • MODEL 526 SySTIUM® TECHNOLOGIES 1. 2. 3. 4. Connect the SATA or IDE HD cable to the hard drive. Route the cable along the bottom of the drive towards the front of the chassis. Connect the floppy cable to the floppy. The route the cable over the HD cable and directly to the other board. Attached the floppy cable to the motherboard. Connect the SATA or IDE HD cable to the motherboard. Route the cable over top the floppy cable. Connect the IDE cable for the 5.
MotherBoard ReadySM System • MODEL 526 SySTIUM® TECHNOLOGIES NOTE Before installing the top side cover please check that all cables are connected and no tools, screws or accessories are left inside the chassis. 1. 2. FIGURE 20 Position the cover down on top of the chassis about 1 inch away to the rear of where the cover’s finally closed position. Slide the cover forward to engage the cover locking tabs to the chassis.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL52 6 ITOX G7V300 ASSEMBLY INSTRUCTIONS I/O Shield The Itox G7V300 motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink on the motherboard with the fan to the front. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHER BOARD READ Y SM SYSTEM • MODEL 526 INTEL DQ35JO ASSEMBLY INSTRUCTIONS I/O Shield The Intel DQ35JO motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL5 26 BCM RX945G ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX945G motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL5 26 BCM RX965Q ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX965Q motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHER BOARD READ Y SM SYSTEM • MODEL 526 INTEL DQ45CB ASSEMBLY INSTRUCTIONS I/O Shield The Intel DQ45CB motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 ITOX BL330-BR ASSEMBLY INSTRUCTIONS I/O Shield 3. The ITOX BL330-BR motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws. See Figure 2.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 ITOX EL330-DR ASSEMBLY INSTRUCTIONS I/O Shield 3. The ITOX EL330-DR motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws. See Figure 2.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 INTEL DG41TY ASSEMBLY INSTRUCTIONS I/O Shield 3. The Intel DG41TY motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws. See Figure 2.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 INTEL DH55TC ASSEMBLY INSTRUCTIONS INSTALLATION OF FRONT PANEL CONNECTORS I/O Shield The Intel DH55TC motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 Advantech AIMB-580 ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The Advantech AIMB-580 motherboard uses the Advantech I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 Advantech AIMB-567 ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The Advantech AIMB-567 motherboard uses the Advantech I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 RadiSys PL35Q ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The RadiSys PL35Q motherboard uses the RadiSys I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 BCM RX35Q ASSEMBLY INSTRUCTIONS Installation of front panel connectors I/O Shield The BCM RX35Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff,(if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526 BCM RX45Q ASSEMBLY INSTRUCTIONS Installation of front panel connectors I/O Shield The BCM RX45Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
MODEL 526 MAINTAINING REGULATORY COMPLIANCE WARNING Read and adhere to all of these instructions supplied for the Model 526 system. Failure to follow these instructions will result in voiding the product’s regulatory compliance statements. Note that the computer system may be noncompliant with other regional product laws and regulations.
ITOX MB331-CRM RadiSys PL35Q (PLV03-0-1) ST350PFC SySTIUM 10304-00C or 10312-25 SySTIUM 10304-00C or 10312-25 ST350PFC Q9400 EM945G RadiSys SySTIUM 10312-25 ST350PFC 3.4GHz 2.66Ghz 3.8 GHz Optional Components: In addition to the required Critical Components listed above Optional Components may be integrated by the assembler/integrator. Optional Components include peripherals (HDD, SSD, optical drives, etc.) and add in /add-on adapters (PCI, PCI-e, USB devices, etc.).
NOTE The peripheral power ratings are typically listed on the product identification label on the peripheral. The manufacturer’s specifications are another source of this information. The load wattage is determined by multiplying the peripheral supply voltage by the peripheral’s maximum current draw for that voltage. For dual voltage peripherals the total load wattage is the sum of each supply voltage’s wattage.
