Assembly Guide Model 526EX 450W 80PLUS
MotherBoard ReadySM System • MODEL 526EX Radio Frequency Interference Notice (USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MotherBoard ReadySM System • MODEL 526EX ASSEMBLY GUIDE Assembly Safety Instructions Before You Begin Assembly of a computer system using this product shall be assembled only by technically qualified personnel. Follow the instructions in the document “Model 526EX Maintaining Regulatory Compliance” to meet and maintain the safety and product regulatory compliance of this product when assembling a computer system using this product.
MotherBoard ReadySM System • MODEL 526EX BULK PACKAGE Please re-cycle the packaging. None of the bulk pack packaging is designed for reuse when shipping to the end customer. CONTENTS The Model 526EX MotherBoard Ready System product contains the following: • • • • 1. The 5.25” peripheral carrier must be removed to install the 5.25 peripheral. 2. Remove the three screws holding the 5.25” carrier to the chassis. Refer to Figure 3 3. Grasp the 5.
MotherBoard ReadySM System • MODEL 526EX 3. 4. Carefully press the top surface of the I/O shield into the I/O opening. Be careful to only place pressure at the outer edges of the I/O shield when pressing on the I/O shield. Check that the I/O shield is fully inserted into the I/O opening. FIGURE 5 NOTE Failure to properly install the I/O shield can result in EMI leakage that will result in the computer system not meeting the product's EMC compliance.
MotherBoard ReadySM System • MODEL 526EX the shouldered 6-32 mounting screws supplied. Refer to Figure 10. Removing the Bezel Filler Panels To remove the peripheral filler panels push the mounting tabs toward each other to release the panel from the bezel. See Figure 8. FIGURE 8 FIGURE 10 Installing a 5.25” External Peripheral Removing the 3.5”EMI Shield NOTE Only when a 3.5”external peripheral is being installed should the 3.5”EMI shield be removed. Failure to install a 3.
MotherBoard ReadySM System • MODEL 526EX 3. Position the second HD carrier such that the mounting tabs locking into the mounting locations on the 5.25 peripheral carrier. Secure the second HD carrier to the 5.25 peripheral carrier using the two supplied screws. Refer to Figure 13. FIGURE 13 Connect Peripheral Cables 1. 2. 3. 4. Connect the SATA or IDE HD cable to the hard drive. Route the cable along the bottom of the drive towards the front of the chassis. Connect the floppy cable to the floppy.
MotherBoard ReadySM System • MODEL 526EX FIGURE 17 The Model 526EX utilizes a power supply with an Energy Hazard on the 12V circuit. Compliance with CE requires installation of the cover lock tab and a lock or the use of the 6-32 TORX screw supplied to secure the top cover. Install the Chassis Feet - Desktop 1. Install the Front USB Module (Optional) NOTE Perform this assembly step if the system requires the front USB ption installed. 2. 3. 1. 2. 3. 4. 5. Remove the front bezel.
MotherBoard ReadySM System • MODEL 526EX Power up the System 1. 2. 3. 4. Connect the keyboard, mouse, monitor and any other required peripheral for the correct operation of the computer. Refer to the Model Guide for assistance in connecting the peripherals to the computer. Turn on the computer by pressing the power switch on the front panel. Refer to the Quick Start Section of this manual for more information. Verify the operation of the POWER ON indicator on the front panel.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX Advantech AIMB-567 ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The Advantech AIMB-567 motherboard uses the Advantech I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX Advantech AIMB-580 ASSEMBLY INSTRUCTIONS motherboard. I/O Shield The Advantech AIMB-580 motherboard uses the Advantech I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installation of front panel connectors Stand Off Installing the Motherboard Connect Peripheral Cables STANDOFF INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX BCM RX35Q ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The BCM RX35Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX BCM RX45Q ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX45Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installation of front panel connectors Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX BCM RX67QV ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX67Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installation of front panel connectors Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX BCM RX965QV ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX67Q motherboard uses the BCM I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installation of front panel connectors Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, (if required) included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX INTEL DH55TC ASSEMBLY INSTRUCTIONS . I/O Shield Installation of front panel connectors The Intel DH55TC motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below. HEATSINK INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX INTEL DQ67OW ASSEMBLY INSTRUCTIONS Installation of front panel connectors I/O Shield The Intel DQ67OW motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below. HEATSINK INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX INTEL DQ67SW ASSEMBLY INSTRUCTIONS I/O Shield The Intel DQ67SW motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installation of front panel connectors Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below. HEATSINK INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX INTEL DQ77MK ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The Intel DQ77MK motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown below. HEATSINK INSTALLATION 1.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX ITOX BL330-BR ASSEMBLY INSTRUCTIONS 3. I/O Shield Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws. See Figure 2. The ITOX BL330-BR motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX ITOX EL330-DR ASSEMBLY INSTRUCTIONS I/O Shield 3. The ITOX EL330-DR motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws. See Figure 2.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX ITOX MB330-CRM ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The ITOX MB330-CRM motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION • Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX ITOX SB330-CRM ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The ITOX SB330-CRM motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION • Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 526EX ITOX SB330-CRM ASSEMBLY INSTRUCTIONS I/O Shield Installation of front panel connectors The Itox SB330-CRM motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION 1. Install the standoff, included in the chassis integration kit, in location 0 as shown in the figure below.
MODEL 526EX MAINTAINING REGULATORY COMPLIANCE WARNING Read and adhere to all of these instructions supplied for the Model 526EX system. Failure to follow these instructions will result in voiding the product’s regulatory compliance statements. Note that the computer system may be noncompliant with other regional product laws and regulations.
NOTE: Effective January 1, 2013 the CE Mark also includes Environmental Conformance Requirements (RoHSII). SySTIUM® maintains a RoHSII technical file for the Model 526EX (and any Critical Component or Optional Component supplied by SySTIUM®) The SySTIUM® Technical File is available upon request and signed NDA.
REGULATORY INFORMATION A computer system, when correctly configured and assembled as instructed in this document, meets the following safety and EMC regulations. SAFETY COMPLIANCE UL 60950-1 Second Edition; CSA60950-1-07 Second Edition Amendment 1:2011 Information Technology Equipment - Safety - Part 1: General Requirements EN 60950- 1:2006/A11:2009/A1:2010/A12:2011; The Standard for Safety of Information Technology Equipment including Electrical Business Equipment.