User manual

Copyright © 2010, Systium® Technologies, LLC
PN: 91018-25
1
MODEL 545 MAINTAINING REGULATORY
COMPLIANCE
WARNINGS
Read and adhere to all of these instructions supplied for the Model 545 system. Failure to follow these instructions will result in
voiding the product’s regulatory compliance statements. The computer system will most likely be noncompliant with other regional
product laws and regulations.
To maintain the CSA listing and compliance to other regulatory certifications and/or declarations the following regulated components must be
used.
You must only use a motherboard listed in the table below. The motherboard must only be used with the CPU model and frequency, and
power supply listed in the table for that motherboard.
MFG
Motherboard
Note
s
Power Supplies
Heat Sink Required
All CPU’s to:
Intel
DH55HC
ST430PFC
Intel Supplied
3.33 GHz
Intel
DP43TF
ST430PFC
Systium 10304-00C
3.0 GHz
Intel
DG43NB
ST430PFC
Systium 10304-00C
3.0 GHz
Intel
DG33FB
ST430PFC
Systium 10304-00C
3.0 GHz
Intel
S3000AH
ST430PFC
Systium 10304-00C
3.73 GHz
Radisys
BG845G, SH845G
ST300PFC
Radisys AVL
3.06 GHz
Radisys
LR915G/BY915GV
ST430PFC
Systium 10304-00C
3.8GHz
Radisys
KP915GV
ST430PFC
Systium 10304-00C
3.8GHz
Radisys
RB945G
ST430PFC
Systium 10304-00C
3.8GHz
ITOX
EL630-NR
ST430PFC
Systium 10304-00C
3.33GHz
ITOX
PT630-NRM
ST430PFC
Intel Supplied
3.33GHz
ITOX
GCB60-BX-N
ST430PFC
ITOX AVL
1 GHz
ITOX
G4V620-B, G4V620-N
ST430PFC
Systium 10300-00C
3.06 GHz
BCM
BC35Q
ST430PFC
Systium 10304-00C
3.0 GHz
BCM
IN915GVE
ST430PFC
Systium 10304-00C
3.8GHz
BCM
RX945G
ST430PFC
Systium 10304-00C
3.8GHz
BCM
RX965Q
ST430PFC
Systium 10304-00C
3.73GHz
POWER SUPPLY Systium ® ST430PFC (10648). NOTE: The Systium 430W power supply is the only supply available. If you require a
replacement for your 300W power supply the 430W is an acceptable replacement. Certifications will not be affected.
CHASSIS You must use the Systium Model 545 without modifications.
ADAPTERS You must use an adapter that is CSA, UL or TUV Listed or Recognized, FCC Class B compliant and CE Marked.
PERIPHERALS You must use a peripheral that is CSA, UL or TUV Listed or Recognized, FCC Class B compliant and CE Marked.
NOTE
 If a Class A device is installed within this system, then the system is to be considered a Class A system.
 The information documented above is updated as required on Systium’s Web Site; www.systium.com. Please check the web site for
information on new supported components and/or processor speeds.
The assembled configuration maximum power load cannot exceed the safety certification configuration maximum power load. The power supply’s output ratings
are higher than the Model 545 system safety certification ratings. Customer configurations should be checked to ensure that the system’s safety certification loads
are not exceeded.
ST430PFC Power Supply Power Budget:
Maximum power consumption cannot exceed 500W AC watts RMS
Peripheral Location
Maximum Power Rating
Notes
5.25” External Drive Bays
75 Watts
4.5A @ 12V, 4.5A @ 5V
3.5 Internal Bays
34 Watts
2.0A@ 12V, 2.0A@5V
I/O Slot Adapters
130 Watts
NOTE
The peripheral ratings are typically listed on the product identification label on the peripheral. The manufacturer’s specifications are another source of
this information. The load wattage is determined by multiplying the peripheral supply voltage by the peripheral’s maximum current draw for that
voltage. For dual voltage peripherals the total load wattage is the sum of each supply voltage’s wattage.