SySTIUM® TECHNOLOGIES Assembly Guide Model 545
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 Radio Frequency Interference Notice (USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MotherBoard ReadySM System • MODEL 545 SySTIUM® TECHNOLOGIES ASSEMBLY GUIDE Assembly Safety Instructions Before You Begin Assembly of a computer system using this product shall be assembled only by technically qualified personnel. Follow the instructions in the document “Model 545 Maintaining Regulatory Compliance” to meet and maintain the safety and product regulatory compliance of this product when assembling a computer system using this product. 1.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 BULK PACKAGE 4. Rotate the top of the cover away from the chassis and then pull the side cover upwards and away from the chassis. Refer to Figure 3. 5. Place the cover to the side where it will not get scratched or damaged before reassembly. Please re-cycle the packaging. None of the bulk pack packaging is designed for reuse when shipping to the end customer.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 FIGURE 5 4. for the motherboard being installed for a figure of the correct installation of the motherboard into the I/O shield. Using the mounting screws supplied, mount the motherboard to the chassis. Ensure that the motherboard is fully inserted into the I/O shield while being tightened into place. Check that the fingers on the I/O shield are in contact with the connectors.
MotherBoard ReadySM System • MODEL 545 SySTIUM® TECHNOLOGIES FIGURE 9 Installing a I/O Adapter (Optional) If an I/O adapter is part of the system configuration the following instructions should be followed. If no I/O adapter is to be installed, then this section can be skipped. 1. Remove the screw holding the I/O slot cover for the I/O slot to be used. Refer to Figure 8 for the location of the I/O slot covers. NOTE 2.
MotherBoard ReadySM System • MODEL 545 SySTIUM® TECHNOLOGIES FIGURE 11 4. Install the second mounting rail on the opposite side of the peripheral. 5. If the 5.25” external peripheral is being installed in the middle bay you must first remove the EMI shield built in to the chassis. The EMI shield can be removed by inserting a flat blade screwdriver into the hook in the EMI shield. The shield can then be rotated carefully to break the mounting clips.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 Installing a 5.25” External Peripheral 4. Configure any jumpers or switch settings require by the peripheral. Refer to the peripheral's user manual for specific instructions. 5. Position the peripheral in the bay with the mounting peripheral mounting screw holes matching the mounting holes in the chassis. Secure the peripheral to the chassis with four of the mounting screws supplied.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 NOTE The 3.5" peripheral carrier supports two 1" high devices or one 1.6' high device. For a second 1" high peripheral please repeat steps 3 and 4 before installing the assembly into the chassis. Connect Peripheral Cables 1. Connect the cables supplied with the motherboard and/or installed peripheral devices.
MotherBoard ReadySM System • MODEL 545 SySTIUM® TECHNOLOGIES Install Side Cover Intel’s Test view. Install any required operating system or application software. NOTE Before installing the right side cover please check that all cables are connected and no tools, screws or accessories are left inside the chassis. 1. Position the lower groove in the side cover to fit onto the lower edge of the chassis. Refer to Figure 21. 2. Close the side cover so as to be flush with the chassis.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL54 5 ITOX GCB60-BX ASSEMBLY INSTRUCTIONS I/O Shield The ITOX GCB60-BX motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION No additional standoffs are required.
S3000AH ASSEMBLY INSTRUCTIONS I/O Shield FIGURE 3 The Intel S3000AH motherboard uses the Intel I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION The S3000AH does not require installation of the brass stand-offs included in the integration kit. These parts can be disposed of. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL54 5 RADISYS KP915GV ASSEMBLY INSTRUCTIONS I/O Shield The Radisys KP915GV motherboard uses the Radisys I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 545 ITOX G4V-620B(N) ASSEMBLY INSTRUCTIONS I/O Shield The ITOX G4V-620B(N) motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. INSTALLATION OF FRONT PANEL CONNECTORS Installing the Motherboard STANDOFF INSTALLATION Install one brass standoff, included in the chassis integration kit, in the location shown in the figure below.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL5 45 BCM BC945G ASSEMBLY INSTRUCTIONS I/O Shield The BCM BC945G motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL5 45 BCM RX945G ASSEMBLY INSTRUCTIONS I/O Shield The BCM RX945G motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL5 45 BCM IN915GVE ASSEMBLY INSTRUCTIONS I/O Shield The BCM IN915GVE motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHER BOARD READ YSM SYSTEM • MODEL 545 DG33FB ASSEMBLY INSTRUCTIONS I/O Shield The Intel DG33FB motherboard uses the Intel I/O shield supplied with the BOX motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL54 5 RADISYS LR915G/BY915GV ASSEMBLY INSTRUCTIONS I/O Shield The Radisys LR915G/BY915GV motherboard uses the Radisys I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM •MODEL54 5 RADISYS RB945G ASSEMBLY INSTRUCTIONS I/O Shield The Radisys RB945G motherboard uses the Radisys I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. 3. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heatsink using the 4 built-in screws.
SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 545 SH845G/BG845G ASSEMBLY INSTRUCTIONS I/O Shield INSTALLATION OF FRONT PANEL CONNECTORS The Radisys SH845G/BG845G motherboard uses the I/O shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure below.
® SySTIUM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 545 BCM BC35Q ASSEMBLY INSTRUCTIONS I/O Shield The BCM BC35Q motherboard uses the I/O shield rear panel supplied with the motherboard. 115V AC or 230V AC Installing the Motherboard The BCM BC35Q motherboard is installed as described in the Model 545 Assembly Guide. No extra steps are required. Installation of Front Panel Connectors Connect Peripheral Cables Refer to the Model 545 Assembly Guide for the suggested peripheral cable routing.
SySTIUM® TECHNOLOGIES MotherBoard ReadySM System • MODEL 545 INTEL DG43NB ASSEMBLY INSTRUCTIONS I/O Shield 3. The Intel DG43NB uses the Intel I/O shield supplied with the motherboard. Turn the motherboard over while holding the support bracket in place. Place the new heat sink mount on the motherboard. Attach the heat sink using the 4 built-in screws. See Figure 3.
MODEL 545 MAINTAINING REGULATORY COMPLIANCE WARNINGS Read and adhere to all of these instructions supplied for the Model 545 system. Failure to follow these instructions will result in voiding the product’s regulatory compliance statements. The computer system will most likely be noncompliant with other regional product laws and regulations. To maintain the CSA listing and compliance to other regulatory certifications and/or declarations the following regulated components must be used.
NOTE Use Only for Intended Applications This product was evaluated as Information Technology Equipment (ITE) that may be installed in offices, homes and similar locations. The use of this product for other Product Safety Categories or Environments other than ITE may require further evaluation. Examples of other Product Safety Categories are Medical Instrumentation or Control and Test Equipment. Check with your Local Product Safety Agency for further information.
