Operating instructions

RQT8152
38
Reference
Error messages
On the television Page
On the unit’s display
Cannot finish recording
completely.
•
•
•
The program was copy-protected.
The disc may be full.
There are already 99 recorded titles ( 49 recorded titles).
—
—
—
Cannot play.
•
You inserted an incompatible disc (Discs recorded in PAL video, etc.). —
Cannot record on the disc.
•
The disc may be dirty or scratched. 42
Unable to format.
Please check the disc.
Cannot record. Disc is full.
•
•
Create space by erasing any unnecessary titles.
(Even if you erase recorded content from a DVD-R or +R, there is no increase in disc space.
Available disc space on DVD-RW (DVD-Video format) increases only when the last recorded
title is erased.)
Use a new disc.
21, 27, 30
—
Cannot record. The number of
titles has exceeded the
maximum limit.
Error has occurred. Please
press ENTER.
•
Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering .
(“oooooo” (self check) appears on the unit display.)
—
No disc
•
The disc may be upside down. —
Please change the disc.
•
There may be a problem with the disc. Press [; OPEN/CLOSE] to remove it and check it for
scratches or dirt. (The unit turns off automatically after you open the tray.)
42
This is a non-recordable disc.
•
•
The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R,
DVD-RW (DVD-Video format) or +R.
You inserted an unformatted DVD-RAM or DVD-RW.
4, 5
30
This disc is not formatted
properly.
5
•
The operation is prohibited by the unit or disc. —
RC
(“ ” stands for a number.)
•
The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
14
Err
•
•
•
•
•
When “Err” appears on the unit’s display, the disc indicator
flashes.
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
You have used a lens cleaner and it has finished. Press [; OPEN/CLOSE] to eject the disc.
You have inserted a disc the unit cannot play or record on.
You have inserted a DVD-RAM or DVD-RW that is unformatted or recorded on other
equipment.
If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
42
—
4, 5
30
—
FULL
•
There are already 16 timer programs. Delete unnecessary timer programs. 19
oooooo
•
•
•
There was something unusual detected with the disc while recording, playing or transferring
(dubbing).
There was a power failure or the AC plug was disconnected while the unit was on. The unit is
carrying out its recovery process.
This process restores the unit to normal operation. The unit is not broken. Wait until the
message disappears.
The symbol “o” appears at the bottom left of the unit’s display.
The number of symbols increases one by one until six appear.
They then disappear one by one from the left until none remain.
This continues during self check.
—
—
40
U59
•
The unit is hot.
The unit switches to standby for safety reasons. Wait about 30 minutes until the message
disappears.
Select a position with good ventilation when installing the unit. Do not block the vent on the
side of the unit.
—
U99
•
The unit fails to operate properly. Press [POWER ^/I] on the main unit to switch the unit to
standby. Then press [POWER ^/I] on the main unit again to turn the unit on.
—
+R
RAM
-RW(V)
TV
RECREC
REC
P
TV
RECREC
P
TV
RECREC
P
DMR-ES20-P10_1.fm 38 ページ ２００５年８月３１日 水曜日 午前１１時４４分