Owners manual

ManualsBrandsBBK Performance ManualsAutomotive4044 Long Tube Exhaust Header Fits 16-19 Camaro

UPDATED LAST: April 2018

WWW.BBKPERFORMANCE.COM

27427 BOSTIK COURT

TEMECULA, CA 92590

For any questions, email us:

tech@bbkperformance.com

IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.

BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.

MADE IN U.S.A.

INSTALLATION INSTRUCTIONS

INS232

2016 - 2018 CAMARO 6.2L V8

FULL LENGTH HEADERS/

CATTED HEAD PIPES

Part #4044 and 40440

Special Tools required: 10mm, 12mm, 13mm, 15mm

Socket and Wrenches, Pliers, Saw, Welder

Diiculty: Average.

NOTE! AUTOMATIC VERSIONS MUST INSTALL 02 SENSOR EXTENSIONS ON DR-SD ONLY.

MANUAL TRANSMISSION DOES NOT APPLY. WELDING AND CUTTING REQUIRED.

INCLUDED IN THIS KIT

(10) 8 x 1.25 x 30mm bolts

(4) M12 x 1.75 x 65mm studs

washers, nuts

(1) 7 inch long heat-wrap

(1) 11 inch long heat-wrap

(5) Zip-ties

(5) Wire-ties

Install Time: Approximately 4-6 hours.

Summary of content (6 pages)

PAGE 1
27427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com INSTALLATION INSTRUCTIONS INS232 2016 - 2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder Install Time: Approximately 4-6 hours. Difficulty: Average. INCLUDED IN THIS KIT (10) 8 x 1.25 x 30mm bolts (4) M12 x 1.
PAGE 2
7427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION STEP 1 STEP 3 Disconnect the negative battery terminal from the battery located in the truck on the passenger side. Place a rag over the trunk latch so the trunk lid will not latch with the battery disconnected.
PAGE 3
27427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION STEP 5 STEP 7 Disconnect the (2) rubber mounting straps that hold the sound tube to the strut brace and A/C line located on the driver side of the engine.
PAGE 4
27427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION STEP 9 STEP 10 Remove the (4) bolts that hold the catted down pipe to the collector on exhaust manifold do this for both driver and passenger sides. Support exhaust system so that it does not fall down. Remove the (4) bolts from exhaust cross member bracket and remove it from the vehicle.
PAGE 5
27427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION STEP 11 STEP 13 Located on the passenger side of the engine bay is the radiator coolant bottle. Remove the 10mm nut that holds the bottle in place. Disconnect the (2) radiator hoses from the fire wall and plug the ends.
PAGE 6
27427 BOSTIK COURT TEMECULA, CA 92590 For any questions, email us: tech@bbkperformance.com FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION STEP 16 for added clearance. Now install header with supplied gasket then install dipstick when header is loose in engine compartment. Now torque header bolts to 30 FT/LB then reinstall,valve cover,spark plugs, wires and then starter heat-shield from underneath the vehicle when installing head-pipes.