Service manual

– 8 –
KDF-E42/50A11E
RM-ED002
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
SECTION 2 GENERAL
13
GB
Getting Started
7: Auto-tuning the TV After selecting the language and country/region, a message confirming the TV start auto-tuning appears on the screen. You must tune the TV to receive channels (TV broadcasts). Do the following to search and store all available channels.
1
Press OK to select “Yes”.
The TV starts searching for all available digital channels followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote. Once all available digital and analogue channels have been stored, the TV returns to normal operation, displaying the digital channel stored on channel number 1. If no digital channels are found, the analogue channel stored on channel 1 is displayed. When a message appears for you to confirm the aerial connections No digital or analogue channels are found. Check all the aerial connections and press OK twice to start auto-tuning again.
2 The Programme Sorting menu appears on
the screen. Note If some digital channel is found, this step will not appear
3 To change the order in which the channels
are stored on the TV. See page 30.
4 Press MENU to exit.
The TV has now tuned in all the available channels.
Tip
functions are available only for countries (page 2).
4 1
Do you want to start
automatic tuning ?
Ye s No
m
Number of Services found 14
Searching. 40%
Digital auto-tune display
m
Auto Tuning
Programmes found:
Searching...
Analogue auto-tune display
19
GB
Using the Menu
Viewing pictures from connected equipment Switch on the connected equipment, then perform one of the following operation. For equipment connected to the scart sockets using a fully-wired 21-pin scart lead Start playback on the connected equipment. The picture from the connected equipment appears on the screen. For an auto-tuned VCR page 11 Press PROG +/-, or the number buttons, to select the video channel. You can also press / repeatedly until the correct input symbol (see below) appears on the screen. For other connected equipment Press / repeatedly until the correct input symbol (see below) appears on the screen or press OK to
access the Input signal index table. Press , to select
an input source, press m/M, then press OK.
Additional operations
Navigating through menus 1
Press MENU to display the menu.
2
Press M/m to select a menu icon, press ,.
3
Press M/m/</, to select an option.
4
Press M/m/</, to change/set the
setting, then press OK.
To exit the menu, press MENU. To return to the last display, press <.
1/ 1, 2/ 2:
Audio/video or RGB input signal through the scart socket / 1 or 2. appears only if an RGB source has been connected.
3:
Component input signal through the Y, P
B
/C
B
, P
R
/C
R
sockets / 3, and audio input signal through the L/G/S/I, R/D/D/D sockets / 3.
4/ 4:
Video input signal through the video socket 4, and audio input signal through the audio socket L/G/S/I (MONO), R/D/D/D sockets 4. appears only if the equipment is connected to the S video socket 4 instead of the video socket 4, and S video input signal is input through the S video socket 4.
5:
RGB input signal through the PC connectors 5, and audio input signal through the socket 5.
6:
Digital audio/video signal is input through the HDMI IN 6 socket. Audio input signal is analogue only if the equipment has been connected using the DVI and audio out socket.
To Do this Return to the normal TV operation
Press DIGITAL or ANALOG.
Access the Input signal index table
Press OK. Press
, to select an
input source, press m/M, then press
OK.
Using the Menu
1 4 2,3,4
Continued