LA I T
Dear customer, Congratulations on your purchase of a Bazooka high-performance amplifier. Rt Bazooka, we are fanatics about accurate music reproduction. Your selection of our products for your sound system indicates that quality sound is also important to you too. Rt SRS, we take great pride in manufacturing revolutionary audio products, and through the years of engineering expertise, hand craftsmanship and critical testing procedures, we have created this high-performance series of amplifiers.
SRFETY PRECRUTIONS Fuse amplifierspower wire at the battery. Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS AMUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors.
FERTURES RND BENEFITS DC OffsetProtection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. ShortCircuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down.
Subsonic Filter (ELR1190, ELR1300, ELR1500 & ELR1BOO) R subsonic filter has been provided to filter out unwanted subsonic bass frequencies below the audible range of the subwoofer. This feature helps to improve the amplifier IS overall performance since power is not wasted reproducing frequencies beyond the speakers ' normal operating range. This feature works in conjunction with the Low-pass crossover to provide band-pass filtering.
MOUNTING LoeRTION 8E!forE! you start thE! installation. it will bE! nE!cE!ssary to find a mounting location for thE! amplifiE!r. Find a location in which thE! amplifiE!r will rE!cE!ivE! adE!QuatE! vE!ntiiation in ordE!r to dissipatE! thE! hE!at it dE!vE!lops during opE!ration. Two popular mounting locations arE! in thE! trunk or undE!r thE! sE!at. SE!IE!ct thE! location in which you wish to mount thE! amplifiE!r. USE! caution whE!n mounting amplifiE!r. thE!rE! arE! many wirE!s. gas linE!s. vacuum linE!s.
POWER CONNECTIONS IN-LINE POWER FUSE MOUNTED WITHIN 12' FROM BATIERY RECOMMENDED (NOT PROVIDED) ~ RADIO'S REMOTE TURN-QN OUTPUT ~~~~ I 94. 7 I c::::::::J c::::::J () I I I I '" I I IMPORTRNT! Before making any connections, disconnect the car's battery until the installation is completed to avoid possible damage to the electrical system. Connect the amplifier to the car's battery. At times.
SIGNRL CONNECTIONS Connect the HCR output of the head unit (RM/FM cassette player, CD, or DRT) to the HCR input terminals of the amplifier. To make these connections, we recommend high quality RCR cables. which arl:! available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise).
HIGH LEVEL CONNECTIONS (OPTIONRL) High Level inputs have been included to connect the amplifier to a radio without low-level outputs (i.e. factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. CRUTION! damag~ to B~for~ making any conn~ctions d~t~rmin~ th~ typ~ of radio to avoid possibl~ and/or radio.
HtoH INPUT LINE IN ",,; ~@~., r.:\. 8A5S BOOST X-OVER 50ttr MAX GAIN • I 94.7 BLACK (GROUND) (NOT USED) GRAYIBLACK GRAY RIGHT ~CH" CH'" C ELA4& I e~'$"!.1 !!i£?~'cO?I LEFT + LEFT- RIGHT- GREEN LINE IN @ ~.()~~Hl "I':;AJ~ 25Ot'11 X-OVER .... CH1/CH2 ... CH' ....- - - GREENIBLACK BAj(:]ST ~~'" ~~P' ~~p'0"~i·3 MIN ~ X..QVER GREEN GREENIBLACK GRAY + + LEFT- RIGHT RIGHT- LEFT + (NOT USED) GRAYIBLACK BLACK (GROUND) - - -......
SPERKER CONNECTIONS Make the speaker connections LIsing speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). Please note that although the ELA1190, ELA1300.
SPERKER CONNECTIONS (BRIDGED) The ELR amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCR connections must be made.
SPERKER CONNECTIONS (TRI-MOOE) The ELR265, ELR2100 and ELR2150 are capable of running in a Mono / stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections.
REMOTE BRSS CONTROL MODULE (OPTIONRL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location. you will need to run the control wire from the remote to the amplifier. To avoid possibility of induced noise from the carls electrical system (Le. popping noises or engine noise), run the cable from the remote to the amplifier away from the carls electrical wiring. SUBSONIC R .
ROJUSTIN6 THE X-OVER RNO BRSS (Please note: If you intend to use the ELR265. ELR2100 and ELR2150 in the Tri-mode configuration, it is necessary to set the crossover control to the "FLRT" setting in order to receive full range output) The "ELR" amplifiers are equipped with a built-in crossover network allowing you to select the crossover type (Le. Low-Pass or Hi-Pass) and the desired crossover point.
TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise.
SPECIFICRTIONS output Power @J 14.4 YOC : 4 ohm 2 ohm Bridged 40hm Bridged 20hm Frequency Response + - 5dB SiN Ratio (A-weight) THO (A-weight) Low Input Level Hi Input Level Battery Yoltage Range Crossover Type Crossover Freq. Range Crossover Slope Bass EO at FULLILP Subsonic Filter Phase Control Unbalanced Input (RCA Jack) Jack for Remote Control Line Output Fuse output Power @J 14.
~ SAS LIMITED WRRRRNTY SouthE!rn Rudio SE!rvicE!s, Inc., warrants all products to bE! frE!E! from dE!fE!cts in matE!rial and workmanship for a pE!riod of onE! (1) yE!ar from thE! date of purchase. In thE! E!vE!nt the product is not as warrantE!d, SRS' solE! obligation shall be to repair or replace thE! defective product at SRS' option: SRS limits its obligation under any implied warranties under state laws to a period not to exceed the limitE!d warranty period.
~ SAS How to obtain warranty services: You are responsible for delivery of the product to an authorized BRZOOKR® dealer or contact SRS at 1-600-THE TUBE for a Return Ruthorization number. The Return Ruthorization number must be clearly written on the outside of the box. Freight must be prepaid to SRS. Warranty replacement parts will be returned freight prepaid. The entire enclosure may be returned for warranty service, but return will be freight collect. 1. 2.
,Q: .SRS. BRZOOKA. BASS TUBES. and LISTEN TO I,I[JLA ERRS are registered trademarks of S © Southern Audio Services. Inc. ml Riahts Reserved. ·ces.lNC.
AMPLIFIER CONNECTION INSTRUCTIONS Far: ELTVB1D19DPP, ELTVBT119DPP ////// Through hole wire path (Note: also available on opposite side) 1. Remove amplifier cover plates 2. Remove screws securing the amplifier to the box 3. Gently lift the amplifier to make necessary wire connections (see amplifier installation manual for detailed wiring instructions). 4. Re-secure the amplifier to the enclosure 5. Re-install the amplifier cover plates Bazooka Mobile Audio· 15049 Florida Blvd· Baton Rouge.
