Installation Instructions

orteR emarF rooD egaraG - tiF dalC snoitcurtsnI noitallatsnI

ooT l deriuqer s

lam rebbur ,edalb gnittuc latem htoot enif a htiw was retim dnuopmoc ,erusaem epat ,rab yrp ,remmah ,)nug wercs( revird wercS ,tel

.sessalg ytefas

vomer ,rab yrp dna remmah a gnisU daehrevo eht morf dluomkcirb doow e d .emarf roo

deen lliw rellif doow a ,ecaf bmaj eht morf laever ”½ a ton si ereht fI .emarf rood egarag eht no laever dluomkcirb eht kcehC eb ot

.ezis tcerroc eht ti ekam ot ecaf bmaj eht ot deilppa

2- 2 ton si ereht fI .gnidis eht fo egde eht ot bmaj rood eht fo ecaf eht morf dedeen si ”2/1 - munimula eht ecaps fo ”2/1

revoc bmaj eht otno pans ton lliw dluomkcirb

rooD egaraG elgniS )rellams dna ediw ’9( - redaeh munimula eceip enO

.A usaeM f er fo ecaf edisni mor eno bmaj ot edis bmaj rehto eht fo ecaf edisni eht t fo htgnel eht enimreted ot edis eh bmaj

revoc .redaeh

.B munimula eht fo ecaf eht ot tnemerusaem siht refsnarT .revoc bmaj

.C a htiw was eht no pu ecaf revoc bmaj eht yaL kcolb doow ti rednu rof ekam dna troppus retim a ot tuc ruoy ta

.kram tnemerusaem

.D tuP ecalp ni revoc bmaj redaeh eht neht dna rood daehrevo drawot drah revoc bmaj hsup .

.E erp hguorht dedivorp swercs eht htiw bmaj doow eht ot revoc bmaj redaeh hcattA - .seloh dellird

W t os bmaj eht ot deilppa gnieb rellif doo munimula eht tah

2 ton si ereht fi dedeen ylno si sihT .tif lliw dluomkcirb - eht morf ”2/1

.gnidis eht ot bmaj doow eht fo ecaf

.rellif eht sa esu rof deppir eb yam doowylP

B ”½ si dluomkcir

.ecaf bmaj morf

PAGE 1
Garage Door Frame Retro-Fit Clad Installation Instructions Tools required Screw driver (screw gun), hammer, pry bar, tape measure, compound miter saw with a fine tooth metal cutting blade, rubber mallet, safety glasses. Using a hammer and pry bar, remove wood brickmould from the overhead door frame. Check the brickmould reveal on the garage door frame. If there is not a ½” reveal from the jamb face, a wood filler will need to be applied to the jamb face to make it the correct size.
PAGE 2
Double Garage Door (over 9’ wide) - Two piece jamb cover header All doors over 9’ wide have a two piece header jamb cover. One end has a miter cut and the other end a ninety degree straight cut. The straight cut end of the jamb cover must be cut so that the clad will butt together in the center of the door opening. We suggest offsetting the seam on the brickmould from the seam on the jamb cover. This will eliminate a continuous line where the two parts meet. F.
PAGE 3
M. Measure from one end of the lower locking point on the header jamb cover to the other end of the header jamb cover. a. N. Divide this dimension in half and then add 1/2” to this measurement for the length of left brickmould piece. The extra ½” will allow for an offset from the jamb cover joint. Transfer this measurement to the face of the left side brickmould. O. Lay the brickmould face up on the saw and make a ninety degree straight cut at your measurement mark. P.