Remote Annex Quick Start for Windows Read before installing and using Remote Annex Software Release 4.2 These installation notes contain information specific to this release. This information is not available elsewhere in the Remote Annex documentation. Part No. 166-024-858 January 1997 Rev.
Copyright © 1997 Bay Networks, Inc. All rights reserved. Printed in the USA. January 1997. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document.
Contents Before Installing the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Windows NT Log On Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 166-024-858 iv Rev.
Remote Annex Quick Start for Windows T his guide is designed for quick installation of a Remote Annex in a Windows NT network environment and configuration of the Annex using Quick2Config Annex. The instructions apply to all Remote Annex models including the Remote Annex 6300.
Remote Annex Quick Start for Windows Before Installing the Software Prerequisites To install Remote Annex Server Tools for Windows NT, you need: • Microsoft Windows NT Server 3.51 or 4.0 configured to support the TCP/IP protocol • Administrative privileges on the server • 10MB free disk space on an NTFS drive • One Windows NT Client 3.51 or 4.
Remote Annex Quick Start for Windows To allow users to log on to the primary domain controller: 1. Choose Policies > User Rights. The User Rights Policy window appears. 2. Select Log on locally from the Right field. The Grant To box displays the names of all groups currently allowed to log on locally. 3. Edit the list using Add and Remove . • To add groups or individual users, click on Add and select individual or group names from the Add Users and Groups window.
Remote Annex Quick Start for Windows To install Remote Annex software on the server: 1. Put the CD-ROM into the Windows NT server’s CD drive. 2. Use the File Manager to select the CD-ROM disk. 3. Double-click on the setup.exe file. 4. Once the setup program runs, the Welcome window appears. Click Next to continue the installation process. Refer to the Installing Remote Annex Network Software for Windows for installation details.
Remote Annex Quick Start for Windows Refer to Installing Remote Annex Network Software for Windows for information about installing the na and Quick2Config Annex software on Windows platforms. If you are installing Quick2Config on a Windows 3.1 or Windows for Workgroups 3.11 platform, you may be required to install additional software that is provided on the CD-ROM. See Installing Remote Annex Network Software for Windows for details. Hardware Setup To set up the Remote Annex hardware: 1.
Remote Annex Quick Start for Windows Network Address After the Remote Annex runs a series of hardware diagnostics, the terminal displays the monitor prompt. Enter address information (step 1) and, if you purchased a LAT key, the LAT key value (step 2). Step 1 procedures are slightly different for the Remote Annex 6300. For illustration purposes, sample response values indicate a Remote Annex on an Ethernet network with the IP address 192.9.200.62. The host system address is 192.9.200.55.
Remote Annex Quick Start for Windows Remote Annex 6300 Remote Annex 5393 1. Enter addr and answer the prompts as shown in the example. To accept the default shown in brackets, press the Return key. monitor:: addr Enter Internet address (hex) :: 192.9.200.62 Enter Subnet mask [255.0.0.0]:: Enter Broadcast address [0.0.0.0]:: Enter Preferred Load Host address []:: 192.9.200.55 Enter Preferred Dump Host address [0.0.0.
Remote Annex Quick Start for Windows Configuring the Remote Annex Remote Annex 2000 Remote Annex 4000 Remote Annex 5390 Remote Annex 5391 Remote Annex 6100 You can configure Annex ports using either Quick2Config Annex or the na utilities. The following examples apply to non-RA 6300 Annexes that have been installed by using default selections. There is a separate configuration procedure for the Remote Annex 6300 and Remote Annex 5393.
Remote Annex Quick Start for Windows Using the na Utility You can also configure Remote Annex ports with the na utilities as shown in the following examples involving non-RA 6300 Annexes installed using default selections. Modems Annex supports inbound, outbound and inbound/outbound modems. When entering port speed, set the highest speed supported by the modem. Do not select autobaud. Set the port parameters using na: % na command: command: command: command: command: command: command: annex 192.9.200.
Remote Annex Quick Start for Windows Serial Printer Serial printers can be connected to any Annex serial port. In this example the printer is connected to port 12. Print instructions use the address L12. Set the port parameters using na and send data to the printer using aprint: % na command: command: command: command: command: command: command: % aprint annex 192.9.200.62 port 12 set port speed 19200 set port type hardwired set port mode slave reset port 12 quit -A 192.9.200.
Remote Annex Quick Start for Windows Configuring Security By default, the Annex allows unrestricted access. If you want to configure Annex security, refer to the Remote Annex Server Tools for Windows NT® User Guide. If you have requested dial-up addresses from the acp_dialup file, refer to the Remote Annex Administrator’s Guide for UNIX for information on adding users to that file.
Remote Annex Quick Start for Windows 2. Modify the following parameters in the external CSU through its front panel: FORMAT (FDL) = ANSI (or ATT) CLOCK = SLAVE DISTANCE = 133 ft. 3. Use na to enable SNMP sets, modify the PRI parameter switch_type if it is other than 5ess (NI-2 or DMS100, for example) and to specify the distance between the Remote Annex 6300 and the CSU. % na command: command: command: command: command: command: annex 129.9.200.
Remote Annex Quick Start for Windows Quick2Config opens an editor with the default configuration file. The Session Parameter Blocks are listed in the %pri section. %pri begin_session sync called_no 123-555-1212 bearer data call_action sync set mode ppp end_session begin_session v120 called_no 123-555-1313 bearer data call_action v120 set mode auto_detect end_session begin_session default call_action modem set mode auto_detect end_session 5.
Remote Annex Quick Start for Windows Configuring Security By default, the Annex allows unrestricted access. If you want to configure Annex security, refer to the Remote Annex Server Tools for Windows NT® User Guide. If you have requested dial-up addresses from the acp_dialup file, see the Remote Annex 6300 Supplement to the Remote Annex Administrator’s Guide for UNIX for information on adding users to that file.
