Instruction Manual

2"
"
3. Due"to"tolerance"stackup"of"components"used"in"the"gapset"assemblies,"there"will"be"a"variation"
as"to"where"the"max"setting"of"each"gapset"knob"will"be."Some"gapset"knobs"may"not"rotate"a"
full"360"degrees"and"stop"at"a"setting"of"13."Som e"gapset"knobs"may"rotate"beyond"360"degrees"
and"stop"at"a"setting"greater"than"the"intended"max"setting"of"15.""
"
B0%$'(>5$(%0(%4$(%09$."2/$(-%"/E57(0#(%4$(/01702$2%-(5-$3(,2(%4,-(6"7-$%("--$1:9&("23(%4$(
70--,:,9,%&(0#(%4$(6"7-$%(:$,26(.0%"%$3(10.$(%4"2(GHI(3$6.$$-("23(60,26(:$&023("(-$%%,26(0#(
)J(.$D5,.$3("(70,2 % (0 #(. $ #$ .$ 2/$(#0.(%4 $ (0 7 $ ." %0 . (%0 (. $ %5 . 2 (%4 $ (6 " 7 - $ %(: " / E (%0 (" (- $ %%,26(0#()*(
F4,-(,-(%4$(029&(75.70-$(0#(%4$(J;)HK)L($9"-%,/(-%07(25%(,2(%4$(6"7-$%("--$1:9&*(
"
4. This"new"type"of"gapset"was"designed"around"20#"(0.0037”"thick)"bond"paper"being"the"most"
common"stock"folded"on"our"floor"model"folders.""This"factor"was"considered"in"both"the"pitch"of"
thread"used "on"th e"ga pse t"kno b/ro d "and "also"th e"de sign"o f"the"ga ps et"kn ob "setting"lab el.""With"
this"fact"in"mind,"each "full"grad ua tion"o n"th e"gap set"kn o b"label"indicates"1"sheet"thickness"of"20#"
bond.""
"
B0%$'(>5$(%0(%4$(70--,:,9,%&(0#(%4$(6"7-$%(E20:(:$,26(":9$(%0(07$2$3(57(7"-%()J(02(%4$(6"7-$%((
E20:@(%4$(07$."%0.(-40593((20%(07$."%$(%4$(#093$.(8,%4("2&;"99(6"7-$%-("%("(-$%%,26(6.$"%$.(
%4"2()J*(+#(%4$(07$ ."%0 .(30 $- (07$ ." %$(%4 $(#0 93$.(8 ,%4 ("2& (0#(%4$ (6" 7-$%-("%(-$%%,26-(6.$"%$.(
%4"2()J@(%4$2(%4 $.$ (,-("(70- -,:,9,%&(0#(%4$ (#093(.0 99-(.5::,26 (%4$ (,2%"E$ -;3 $#9$/%0 .-(0#(%4 $(#093(
7"2-*(F4,-(80593(/"5-$(7.$1"%5.$(8$".;3"1"6$(%0(%4$(#0937"2-;#093(.099-*(
(
"
Plastic"Binder"Plug"
Set"Screw
Cap"
Gapset"Knob"
Gapset"Setting"Dial"Indicator"w/"Label"
Foldhead"Frame "
Fold"Roll"
Ela stic"Stop"Nut"
Gapset"Rod/Block"
Weldment"