Datasheet

ManualsBrandsBaumer Electric ManualsAngle & Rotary SensorsIncremental Rotary Encoder 65536 PPR 4.75 ... 30VDC 6000min -1

www.baumer.com/motion

Incremental encoders

Subject to modication in technic and design. Errors and omissions excepted.9/5/2019

EIL580P-T with through hollow shaft

Features

– Size ø58 mm

– Precise optical sensing (interpolated)

– Output signal level programmable (TTL or HTL)

– Through hollow shaft, ø8…15 mm

– Connection radial or tangential

– Pulses per revolution 1...65536, programmable

– High protection up to IP 67

– High resistance to shock and vibrations

Technical data - electrical ratings

Voltage supply 4.75...30 VDC

Reverse polarity protection Yes

Short-circuit proof Yes

Consumption w/o load ≤70mA

Initializing time ≤30msafterpoweron

Pulses per revolution 1...65536

Duty cycle 45...55 % typical at 1024, 2048

ppr (further see table Duty

cycle)

Reference signal Zero pulse 90° or 180°

Sensing method Optical

Output frequency ≤300kHz(TTL)

≤160kHz(HTL)

Output signals A+,B+,R+,A-,B-,R-

Output stages TTL/RS422

HTL/push-pull

Programmable

parameters

OutputlevelTTL/HTL

Pulse number 1...65536

Zero pulse width 90°/180°

Zero pulse position

Signal sequence

Interference immunity DIN EN 61000-6-2

Emitted interference DIN EN 61000-6-3

Approval UL508/CSA22.2

EIL580P-T - OptoPulse

Technical data - mechanical design

Size(ange) ø58 mm

Shaft type ø8...15 mm (through hollow

shaft)

Protection DIN EN 60529 IP 65 (without shaft seal),

IP 67 (with shaft seal)

Operating speed ≤3000rpm(+20°C,IP67)

≤6000rpm(+20°C,IP65)

Starting torque ≤0.025Nm(+20°C,IP65)

≤0.03Nm(+20°C,IP67)

Materials Housing:aluminiumdie-cast

Flange:aluminium

Operating temperature -40...+100°C

Relative humidity 90 % non-condensing

Resistance DIN EN 60068-2-6

Vibration30g,10-2000Hz

DIN EN 60068-2-27

Shock250g,6ms

Connection Flange connector M12, 8-pin

Flange connector M23, 12-pin

Cable

Weight approx. 300 g

With through hollow shaft

1…65536 pulses per revolution programmable (interpolated system)

Summary of content (8 pages)

PAGE 1
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Features –– Size ø58 mm –– Precise optical sensing (interpolated) –– Output signal level programmable (TTL or HTL) –– Through hollow shaft, ø8…15 mm –– Connection radial or tangential –– Pulses per revolution 1...
PAGE 2
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Part number EIL580P- T . F . 01024 . B Operating temperature B -40...+100 °C Pulses programmable 01024 1...65536 programmable (factory setting: 1024) Voltage supply / output stages F 4.75...
PAGE 3
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Accessories Accessories Connectors and cables Mounting accessories 10127844 Connection cable 2 m shielded with female connector M12, 8-pin, straight (ESG 34FH0200G) 11155325 10129332 Connection cable 5 m shielded with female connector M12, 8-pin, straight (ESG 34FH0500G) Mounting plate, 1-arm, pitch circle diameter ø95 mm, mounting M6, isolated, rigid, suitable fo
PAGE 4
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Output signals Terminal assignment Flange connector M23, 12-pin / cable Zero pulse electrical 90° A&B high (Factory setting at clockwise rotation (CW) in view of the encoder flange) A+ A- B+ B90° Assignment 1 pink B- 2 – – 3 blue R+ 4 red R- 5 green A+ 6 yellow A- 7 – R-Set 1) 8 grey B+ 9 – – 10 white GND 11 – – 12 brown UB Screen:
PAGE 5
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Duty cycle The duty cycle (D) is defined as the time ratio between the HIGH pulse duration (H) and the pulse period (T). System-induced and depending on the pulse number, the measured values may vary which has an impact on speed and position acquisition. Binary pulse numbers are recommended for speed feedback.
PAGE 6
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Dimensions Clamping ring at A-side: Through hollow shaft, flange connector M12 radial 70 ø63 4 37.5 14.5 70 ø63 ø31 ø58 3.5 14.4 15.5 43 Clamping ring at A-side: Through hollow shaft, cable radial 37.5 4 70 ø63 14.5 4 14.5 ø31 ø58 H d 15.1 15.5 11.8 15.1 15.5 5 43 43 6 www.baumer.com/motion Subject to modification in technic and design.
PAGE 7
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Dimensions Clamping ring at B-side: Through hollow shaft, flange connector M12 radial 70 ø63 ø58 ø31 56 d 3.5 M12x1 11.8 M23x1 15.5 43 15.1 14.3 15.1 43 Clamping ring at B-side: Through hollow shaft, cable radial Flange version M: Mounting position torque support 48.5 37.5 70 ø63 180° 4 26 ø31 ø58 14 2 270° 90° ~ 53 d 3.5 11.8 15.5 15.
PAGE 8
Incremental encoders With through hollow shaft 1…65536 pulses per revolution programmable (interpolated system) EIL580P-T - OptoPulse® Dimensions $ $ ¡ $ Flange version P: Pin torque support, axial, clamping ring at A-side $ Clamping ring at A-side: Through hollow shaft Clamping ring at B-side: Through hollow shaft &XVWRPHU VKDIW PLQ 8 Subject to modification in technic and design. Errors and omissions excepted. PLQ www.baumer.