BG60TCBL/BG60TCSS/BG60TCW 60 cm 4 Burner gas hob with thermocouples BT62TCSS 60 cm 4 Burner gas hob with thermocouples B68TCSS 70 cm 5 Burner gas hob with thermocouples 1
User Manual for your Baumatic BG60TCBL/BG60TCSS/BG60TCW 60 cm 4 Burner gas hob with thermocouples BT62TCSS 60 cm 4 Burner gas hob with thermocouples B68TCSS 70 cm 5 Burner gas hob with thermocouples NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications BG60TCBL/SS/W BT62TCSS B68TCSS Electrical details Gas details Gas hob surface layout 8 – 12 8 9 10 11 11 12 Using the gas hob Before first use Switching the hob on Push button ignition with flame failure safety device (BG60TCBL/SS/W) Automatic ignition with flame failure safety device (BT62TCSS/B68TCSS) Energy saving tips 13 - 15 13 13 13 – 14 Cleaning Cleaning the hob top After each use Cleaning the hob burners Maintainin
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a CORGI registered installer, strictly in accordance with the manufacturer’s instructions and the relevant British Standards. Please see the specific section of this booklet that refers to installation. o Baumatic Ltd.
Specifications BG60TCBL/SS/W Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
BT62TCSS Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.30 kW wok burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B68TCSS Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 510 mm 685 mm 35 mm 480 mm 560 mm Product specifications: o o o o 1 1 2 1 x x x x 3.30 3.00 1.75 1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230 Vac 50 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.008 to 0.02 kW (depending on model) 3 core x 0.75mm² Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.9 mbar), Alternative LPG G30 (28-30 mbar), Town gas G110 – 120 (8 mbar) to order.
Gas hob surface layout BG60TCBL/SS/W BT62TCSS B68TCSS 12
Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Switching the hob on The following symbols will appear on the control panel, next to each control knob: 0 = gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
o After this 20 second interval, turn the control knob to your required setting between the maximum and minimum setting symbols. o To turn the burner off, turn the control knob fully clockwise to the gas off position. o In case of power failure, the burners can be lit by carefully using a match.
Energy saving tips BURNERS PANS Minimum Maximum diametre diametre Wok 220 mm 260 mm Rapid 180 mm 220 mm Semi-rapid 120 mm 200 mm Auxiliary 80 mm 160 mm o The diametre of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametre of the pan. o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is not blocked. o IMPORTANT: Make sure that you reassemble the burners in the original way. Maintaining cast iron pan stands (BT62TCSS/B68TCSS) o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them. o Wipe the pan stands over with a soft, damp cloth that has been put into warm soapy water.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 2 x Pan stands 3 x Pan stands (B68TCSS) 4 x Burner assemblies 5 x Burner assemblies (B68TCSS) 1 x Installation and instruction manual 1 4 4 1 4 5 x x x x x x Baumatic guarantee card Fixing screws Clamps Sealing strip LPG jets LPG jets (B68TCSS) 1 x Self-adhesive label for amending the Gas Category on the appliance’s rating plate (required if the LPG conversion k
o Cut a hole in the worktop that corresponds with the drawings shown on page 19. o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop.
Ventilation requirements o The room containing the hob should have an air supply in accordance with the current edition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area). Unless it has a door which opens directly to the outside. o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area).
Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a ½ BSP Elbow, seal, copper pipe and an isolation tap fitted in an easily accessible position. o It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the Gas Safety Installation and Use Regulations. o It is in your interest and that of safety to ensure compliance with the law.
Gas adjustment (Conversion to LPG) All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A). o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). GENERAL INJECTORS TABLE Kind of gas Nozzle Burners Power (in watts) mm/100 Max. Min.
o IMPORTANT: The minimum flow adjustment process must be completed before the appliance is next used. Minimum flow adjustment for hob gas taps. All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a CORGI registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 0.75 mm³ (Type RR-F marked). o The mains supply cable is supplied with this product.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Republic of Ireland 01- 6266 798 Czech Republic Baumatic CR spol s.r.
