BDW17 60 cm Fully integrated full height electronic dishwasher Downloaded from DishWasher-Manual.
USER MANUAL FOR YOUR BAUMATIC BDW17 60 cm Fully integrated full height electronic dishwasher NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance. DD 26/02/2008 Downloaded from DishWasher-Manual.
Contents Environmental note 4 Important safety information 5–7 Specifications Product and aperture dimensions Product specifications Energy efficiency details Electrical details 8 8 8 8 9 Description of the appliance Control panel LED display 9 10 10 Using your dishwasher Before first use Filling with dishwasher salt Setting the water softener level Filling with rinse aid Setting the rinse aid level Filling with dishwasher detergent Loading the upper basket Adjusting the upper basket Loading the low
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Technical Department. General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents.
o No attempt should be made to alter or modify the specifications of this appliance. In daily use o This appliance is only designed to wash normal domestic washloads. If you use your dishwasher in any other way or it is incorrectly used, then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void. o It is recommended that the appliance is unplugged and the water supply is turned off after the machine is used.
Child Safety o Your dishwasher should only be used by adults. You should not allow children in the area of the machine unsupervised. You should not let them touch the controls or play with the appliance. o It could be possible for a child or pet to gain access to the dishwasher if the door is left open. Therefore please check the inside of the appliance before setting it on a wash cycle. o Any packaging that is removed from the machine should be kept away from children.
Specifications Product dimensions: Product dimensions Height: Width: Depth: 820 mm 595 mm 540 mm Aperture dimensions Height: Width: Depth: 820 mm (min) 600 mm 570 mm (min) Product specifications o 14 Place settings o 7 functions: Normal Intensive Economy Rinse Glass Rapid 3 in 1 o o o o o o o o o o o o o 4 Wash temperatures: 40°C, 45°C, 50°C, 60°C Delay timer LED display Self-cleaning stainless steel microfilter Electronic aqua stop Anti-leak device Anti-flood device Height adjustable upper basket Coll
Electrical details Rated voltage: 230 Vac 50 Hz Supply connection: 13 A (double pole switched fused outlet with 3 mm contact gap) Optional extra o DWD600SS- Stainless steel door with mark resistant coating Description of the appliance 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) Upper basket Spray arms Lower basket Water softener Main filter Detergent dispenser Cup shelf Cutlery basket Coarse filter Rinse aid dispenser Drain pipe connector Inlet pipe connector Downloaded from DishWasher-Manual.
Control panel 1) 2) 3) 4) 5) 6) ON/OFF button Power on neon ½ load button Delay start button LED display Program selection button LED display The LED display can show the following information:o o o o o o o o o o o o o Salt required 3 in 1 wash program selected Rinse aid required 1/2 load wash program selected Wash program time indicator Delay start time set Intensive wash program selected Normal wash program selected Economy wash program selected Rinse wash program selected Glass wash program selected
Using your dishwasher Before first use o Install the appliance as per the installation instructions contained within this booklet. o Fill the water softener with 1 litre of tap water and then fill with specialist dishwasher salt. After this you should set the water softener level. o Fill the rinse aid dispenser and then set the rinse aid dosage. Filling with dishwasher salt IMPORTANT: You should only use salt that is specially designed for use in a dishwasher.
o It is perfectly normal for a small amount of water to come out of the salt container, whilst you are filling it with salt. This does not mean that the container is filled with the correct amount of salt. o Refit and fully tighten the salt container cap. o The salt required warning light will go out approximately 2-6 hours after you have filled the salt container with salt. When the salt required warning light comes on again, then you should follow the filling with dishwasher salt procedure again.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets and live in a medium or hard water area, then you should still fill the water softener with salt. The water softener arrow should be turned to the minus setting. Filling with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes. These droplets will lead to spots and streaks being left on items after the wash program has completed.
Setting the rinse aid level The amount of rinse aid that the dishwasher requires also depends on the hardness of your water. You should experiment with the rinse aid setting, until you find a level that gives the best results. o On the first wash cycle, we would recommend that the rinse aid level is set to number 2. o If you get water spots and poor drying performance, then you should turn the arrow anticlockwise and increase the setting to the next number.
o At the beginning of a wash cycle the clip will open and the tablet/powder/liquid will enter the dishwasher. Loading the upper basket The upper basket is most suited to washing delicate and light dishware, such as glasses, coffee & tea cups, saucers, plates, bowls and shallow pans (that are not heavily soiled). 1. 2. 3. 4. 5. 6. 7.
Position 2 (lower position) o For accommodating additional tumblers, cups and mugs. You can also place small, espresso sized cups on top of the side racks. Care should be taken to make sure that there is enough clearance between the top of the cups placed on top of the side racks and the underneath of the dishwasher interior. o Please note that when the basket is in the upper position, you cannot have the side flaps in a raised position.
o Deep saucepans should be slanted, to allow water to run off. o The bottom rack has prongs at the rear of the basket that can be folded downwards, to allow for easier loading of larger saucepans and serving bowls. The cutlery basket Cutlery should be placed inside of the cutlery basket. The cutlery basket should then be placed in the appropriate position in the lower basket. o For the best washing performance, cutlery should be placed through the slots in the top of the cutlery basket.
Loading dishes and cutlery Household cloths, sponges or any other object that may absorb water SHOULD NOT be washed in a dishwasher. o Remove leftovers and soften the remnants of burnt food in pans, prior to loading dishes in the appliance. o Once the dishwasher has been loaded, check that the spray arms can move freely. If the spray arm comes into contact with any item, then you should rearrange the wash load.
The following items are NOT suitable for washing inside a dishwasher:o Cutlery with a handle of mother-of-pearl, wood, horn or china. o Plastic items that are not resistant to heat. o Cutlery that consists of glued parts that are not resistant to heat. o Cutlery items or crockery that are bonded. o Copper or pewter items. o Lead crystal glass. o Wooden platters o Synthetic fibre items.
Program table * Normal is the testing program for EN 50242. Setting a wash program Make sure that the before first use section has been followed. o Check whether the appliance needs rinse aid or salt adding to it. o Pull out the top and bottom baskets, then load them in accordance with the loading instructions. o Push the top and bottom baskets fully back into position. o Add detergent o Turn the appliance on by using the ON/OFF button. Downloaded from DishWasher-Manual.
o IMPORTANT: Wait for 5 seconds before pressing the program selection button, otherwise the appliance may not function correctly. o Press the program selection button to choose an appropriate wash program for the load that you are washing. The program that you have selected will light up in the LED display. o Select any program options that you want to use (e.g. delay start or half load). o Close the door firmly, so that you hear the door lock click shut.
At the end of a wash program o The time display will flash for 8 seconds and a buzzer will sound. o If you have used the delay start mode, the time display will flash for 8 seconds but the buzzer will not sound. o Open the door of the appliance. o Use the ON/OFF button to switch the dishwasher off and unload the dishwasher. The 3 in 1 wash program Make sure that the water softener has been filled with salt and that the water softener has been set to its lowest setting.
If your wash results are poor, then we would recommend that you use a dishwasher detergent that doesn’t have rinse aid and salt included in the tablet. The water softener should then be adjusted to an appropriate level for the hardness of the water in your area. Setting a delay start It is possible to delay the start of the wash program for up to a maximum of 24 hours. o Check whether the appliance needs rinse aid or salt adding to it.
Setting a half load The half load option means that the lower spray arm does not run. IMPORTANT: You should only load items in the upper basket when using the half load option. o Check whether the appliance needs rinse aid or salt adding to it. o Pull out the top basket, and then load it in accordance with the loading instructions. o Push the top and bottom baskets fully back into position. o Add detergent o Turn the appliance on by using the ON/OFF button.
Cleaning and maintenance IMPORTANT: The appliance should be disconnected from your mains supply before commencing any cleaning process. The filter system Your appliance is fitted with three levels of filtering; these are located in the base of the dishwasher for ease of access. 1) Main filter 2) Coarse filter 3) Fine filter Main filter- Food and soil particles are trapped by this filter and pulverised by a special jet on the lower spray arm. This debris is then washed down the drain.
Cleaning the filters For best performance and results, the entire filter assembly should be thoroughly cleaned regularly (ideally after each wash cycle). 1. Turn the coarse filter anti-clockwise and then lift it upwards. Rinse out this section under a tap to remove any food debris that remains in it. 2. Pull out the main filter and rinse this under the tap to remove any food debris that is trapped in it. 3.
Cleaning the spray arms The spray arms should be cleaned regularly, to prevent hard water deposits from clogging the spray arm jets and bearings. o To remove the spray arm, unscrew the nut and take out the washer that sits on top of the spray arm. o Gently pull upwards to remove the spray arm. o Wash the spray arm in warm, soapy water and use a soft brush to clean the jets. o Rinse the spray arm thoroughly and then reassemble the spray arm back in its original position.
Cleaning the door o To clean the edge around the outside of the door, you should use a soft, damp cloth only. o To prevent water from penetrating the door lock or electrical components, DO NOT use a spray cleaner of any kind. o DO NOT use any abrasive cleaner or scouring pads on the inner or outer surfaces, as they may cause damage to them. Error code failure system If your appliance senses that it is not operating correctly, then an error code may appear in the display window.
E4 o The machine has sensed water in the base. 9 Check that the outlet hose is not kinked or crushed. 9 Check that there are no blockages in the drain hose or the drainage system that the appliance is connected to. 9 The drain pipe may be placed in too high a position or incorrectly. Check the installation instructions and ensure that the installation is correct. E5 o Switch cannot shut off automatically- program not finishing its cycle. 9 Low voltage or power switch failure.
IF THE FAULT CODE REAPPEARS AFTER FOLLOWING THE ABOVE ADVICE AND CLEARING THE FAULT CODE. YOU SHOULD TURN OFF THE APPLIANCE; DISCONNECT THE APPLIANCE FROM YOUR MAINS SUPPLY. THEN ARRANGE FOR AN ENGINEER TO ATTEND THE APPLIANCE. YOU SHOULD CONTACT BAUMATIC SERVICE ON TELEPHONE NUMBER (0118) 933 6911. IF AN ENGINEER ATTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST, WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER.
Suds in the tub Improper detergent use Spilled rinse aid Ensure that you are not using 3 in 1 detergent tablets, in conjunction with rinse aid and salt. Always wipe up any excess rinse aid or rinse aid spillages immediately. Stained tub interior Dishes are not fully dried Detergent with colourant was used Rinse aid dispenser is empty Use a detergent without colourant. Dishes and pans are not clean Improper program Select a more intense wash program.
Installation IMPORTANT: THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON. BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL. YOU SHOULD DISPOSE OF ALL PACKAGING IN AN ENVIRONMENTALLY FRIENDLY MANNER. Aperture requirements o The aperture that your dishwasher needs to be installed into should resemble the one in the drawings above. o There should be less than a 5 mm gap between the top of the dishwasher and the underneath of the worktop.
Installation stages 1. 2. 3. 4. 5. 6. 7. 8. 9. Preparing and connecting the furniture door. Adjusting the tension of the door spring. Connecting to the mains water supply Connecting to the water outlet Connecting to the power supply Applying the condensation strip Positioning the dishwasher Levelling the dishwasher Securing the dishwasher Preparing and connecting the furniture door o IMPORTANT: The furniture door is not supplied with the appliance.
o Attach the upper hooks onto the furniture door. o Attach the lower hooks onto the furniture door. o Lift the furniture door towards the dishwasher door, ensuring that the upper and lower hooks locate into the slots on the outside of the dishwasher door. o Push the furniture door downwards so it locks into place on the dishwasher door. o Open the dishwasher door and find the covers that are located on either side of the outer edge. o Fully tighten the screws into the holes.
Adjusting the tension of the door spring o The door of the dishwasher is attached to springs. These are set at the factory to ensure that they are at the proper tension, so that the door can open and close smoothly. o After the furniture door has been adjusted, you will need to adjust the tension of the door spring. o Using an Allen key, rotate the adjusting screw to either tighten or slacken the steel cable.
Connecting to the mains water supply IMPORTANT: Do not connect the appliance to your mains water supply using an old or an existing water inlet hose. The inlet hose supplied with the dishwasher is the ONLY one that should be used. DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP. o The inlet hose will be located inside the cabinet of the dishwasher. o Connect the water inlet hose to a threaded water tap that has a 3/4” thread and to the inlet hose connector on the appliance.
Connecting to the water outlet 9 Secure the drain hose, so that it cannot move whilst the dishwasher is in use. 9 Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe. 9 IMPORTANT: Do not insert the drain hose too deeply into the pipe, as this may cause siphoning. 9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH. Connecting to the power supply 9 IMPORTANT: The electrical socket must still be accessible once the appliance is installed.
9 Consult the rating plate, located on the right hand side of the drop down door BEFORE making the electrical connections. Ensure that the voltage reaching the plug is the same as that on the rating plate. 9 DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT. 9 The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket. 9 Broken or damaged power leads must only be replaced by a suitably qualified person.
o Ensure that the underneath of the worktop is clean before sticking the strip to it. o Separate the backing paper away from the strip. o Stick the condensation strip to the underneath of the worktop. o IMPORTANT: Failure to attach the condensation strip could result in damage to your worktop. Positioning the dishwasher o Place the feet of the dishwasher into the slide rails. o Carefully slide the dishwasher back into position, underneath the worktop. Downloaded from DishWasher-Manual.
Levelling the appliance o IMPORTANT: Your dishwasher must be level for it to operate properly. o Make sure that the dishwasher is supported whilst it is being levelled, otherwise it may tip over. o The rear feet can be adjusted by using the adjusting screw at the front of the appliance. o The front feet can be adjusted using a spanner. o Use a spirit level to check that the appliance is level. o Check that the appliance is level from side to side. o Check that the appliance is level from front to back.
Securing the dishwasher o The dishwasher must be secured to the worktop, this can be done in one of two ways:o Standard worktop- Secure the dishwasher to the underside of the worktop by using two wood screws. o You should screw through the holes in the brackets at the top of the dishwasher cabinet. o These screws should be fully tightened. o Marble/granite worktop- The material of the worktop will mean that it is impossible to put a screw through the underneath of the worktop.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Czech Republic Baumatic CR spol s.r.o. Amperova 495 46215, Librec Czech Republic Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Service Telephone (0118) 933 6911 Service Fax (0118) 986 9124 Spares Telephone (01235) 437244 Technical Advice Telephone (0118) 933 6933 www.baumatic.cz E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.
Downloaded from DishWasher-Manual.
2 Downloaded from DishWasher-Manual.
