s Spare parts list for Candy model Supplier model number:HJA26017119 550m3/H For whole cooker hood B20-2201-004-P 1 B20-2201-006-P 2 3 B71-4301-007-B 4 B76-4301-001-B B35-2201-038-0 5 B35-2501-014-0 6 B76-4308-004-B 7 B30-2201-079-0 8 B65-2201-081-0 9 B62-2201-087-0 10 B64-2501-108-0 11 B30-2201-078-0 12 B23-2201-012-P 13 B23-2201-010-P 14 B23-2201-008-P 15 B62-2301-070-0 16 B30-2502-015-0 17 18 19 20 21 22 23 24 25 26 27 For motor accessory : 120mm outlet adaptor 1 1 1 1 3 2 1 1 2 2 1 1 1 1 1 1 1 US
Baumatic Spare parts list for Baumatic model F60.
F60.2-BL/SS F70.2-BL/SS F90.
User Manual for your Baumatic F60.2-BL/SS 60 cm cooker hood F70.2-BL/SS 70 cm cooker hood F90.2-BL/SS 90 cm cooker hood NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5–7 Specifications of your cooker hood F60.2-BL/SS F70.2-BL/SS F90.
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed.
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room.
o Note: Your cooker hood is designed to remove cooking odours from the room and not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose. o Do not install above a cooker with a high level grill.
Specifications of your cooker hood F60.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 600 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 172 mm x 222 mm Your stainless steel cooker hood is fitted with: o o o o o o Integrated centrifugal motor Push button control operation 3 Speeds 2 Washable metallic grease filters 2 lights Extraction or recirculation Extraction capacity: 550 m³/hr Optional extra: Carbon filter MODEL NUMBER CARBON FILTER REQUIRED F60.2-BL/SS-AR ST2 F60.
F70.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 700 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 172 mm x 222 mm Your stainless steel cooker hood is fitted with: o o o o o o Integrated centrifugal motor Push button control operation 3 Speeds 2 Washable metallic grease filters 2 lights Extraction or recirculation Extraction capacity: 550 m³/hr Optional extra: Carbon filter MODEL NUMBER CARBON FILTER REQUIRED F70.2-BL/SS-AR ST2 F70.
F90.2-BL/SS PRODUCT DIMENSIONS Height: 638–1080mm* Width: 900 mm Depth: 500 mm DIMENSIONS OF CHIMNEY SECTION: 172 mm x 222 mm Your stainless steel cooker hood is fitted with: o o o o o o Integrated centrifugal motor Push button control operation 3 Speeds 3 Washable metallic grease filters 2 lights Extraction or recirculation Extraction capacity: 550 m³/hr Optional extra: Carbon filter MODEL NUMBER CARBON FILTER REQUIRED F90.2-BL/SS-AR ST2 F90.
Optional extras (all models) DK5 1 Metre length Ducting Kit 125 mm Ø. DK10 3 Metre length Ducting Kit 125 mm Ø with flat channelling included. o Available from the Baumatic Spares Department. Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner and polish on ALL of the stainless steel areas of your cooker hood, before it is used for the first time.
o Find the control panel, which is located at the front right of the canopy. o There are several buttons on the control panel, which perform separate functions. IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING.
The grease filters o Your cooker hood is fitted with grease filters, which help to absorb grease particles and protect your kitchen and furniture from greasy residues. o These metallic filters may become inflammable if you allow them to get saturated with this greasy residue. o To prevent this fire hazard, the filters should be cleaned regularly. Depending on use, this should be done every 10-15 days or at least once a month, using hot water and normal washing-up detergent.
Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove the grease filters (as described on page 15). o Prior to touching the light bulbs ensure they are cooled down. o Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy. o Unscrew the light bulb that needs to be replaced and insert a new E14 40W (max) bulb.
Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE RANGEHOOD FROM YOUR MAINS SUPPLY. 1) Remove the grease filters. 2) Press the carbon filter against one end of the motor, the fixing point is in the centre of the carbon filter.
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filter.
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. o The brown wire must be connected to the terminal marked “L” (live), or coloured red. Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area.
o Do not tile, grout or silicone this appliance to the wall. This appliance is designed to be surface mounted only. Installing your cooker hood IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGE 28 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES. o We recommend that at least two people install this hood. o All images are for reference only.
2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit, make holes in the wall on the positions that you have marked in step 2. 4) Insert rawl plugs into all of the holes that you have drilled. 5) Fasten the support screws halfway in, leaving them 10 mm out of the wall.
6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Fully tighten the anchoring screws into the wall.
Connecting to external ducting Important: To get the optimum performance from your appliance, 150mm ducting should be used. 8) Connect a 150 mm ducting hose to the opening at the top of the motor/hood. (Please note that the ducting hose is not supplied with the appliance). o If you choose to use 125mm ducting, then please fit the reducer adaptor (supplied). o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours.
10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the side measurements of both sides of chimney section (D) on the wall with a pencil and then remove chimney section (D). 11) Take the flat bracket (E) and place it between the two pencil marks that you made in step 9 o Keeping the bracket in contact with the wall, use a pencil to mark on the wall the anchoring holes that are cut out of the bracket.
12) Using a 6 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and then use a screwdriver to secure the fixing bracket to the wall. o Refit chimney section (C) to the hood and fix it onto the hood using the two screws that are supplied. o Secure the top of chimney section (C) to the flat bracket, using the screws provided. o Slide chimney section (D) inside of chimney section (C).
Completing the installation o If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitting the carbon filters” section on page 15. o The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply. See page 16 - 17 for detailed information on the electrical connection.
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. My cooker hood is not working effectively. o The fan speed is not set high enough o The grease filters are dirty and require cleaning. o The kitchen is not well ventilated enough.
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Czech Republic/Slovakia Baumatic s.r.o.
28
