Manual

EMPIREPAINTBALL.COM
8
Note: Selector position (0) is used as a Safety in all Modes.
Value 1 - Semi-Auto/NPPL – One shot per trigger pull. Max ROF
capped at 20 BPS.
Value 2 - Ramping/PSP – The TM-7 will operate in Semi-Auto mode for the
first 3 safety shots; then if player maintains at least one pull per second,
the TM-7 will fire ‘X’ number of shots per pull and release of the trigger as
defined by function 6 (burst shots) at the rate of fire defined by function 2.
No trigger pull within one second of the last pull will reset the mode and
the user must fire 3 more safety shots to continue burst shots.
Value 3 - Full-Auto/NXL – The TM-7 will operate in Semi-Auto mode for
the first 3 safety shots; then pull and hold trigger on the 4th shot, and
the TM-7 will fire full-auto at the Rate of Fire value in Function 2, which is
defaulted to 13 shots per second for this mode.
Value 4 - Ramping/Millennium – The TM-7 will operate in Semi-Auto
mode until player achieves the minimum trigger pull as defined by the
Ramping Point value in Function 5, which is defaulted to 6 trigger pulls
per second for this mode. At that point, and as long as 6 trigger pulls
per second are maintained, the TM-7 will ramp to the Rate of Fire value
in Function 2, which is defaulted to 12 shots-per-second for this mode.
Value 5 - Recreational Mode - Selector Switch Position (1) - Standard
Semi-automatic- Max ROF capped at 20 BPS.
Selector Switch Position (2) - See Value 2 - Ramping/PSP.
Selector Switch Position (3) - The TM-7 will operate in Semi-Auto mode for
the first 3 safety shots; then pull and hold trigger on the 4th shot, and
the TM-7 will fire NXL full-auto at the Rate of Fire value in Function 2.
Note: If you activate the Tournament Lock on your TM-7 while in
Recreational mode, all of the Selector Switch positions will still be live.
Note: After modes 2 through 4 are selected, it is possible to raise or
lower both the Rate of Fire and Ramping Point values in case the tourna-
ment rules change.
Max Rate of Fire (ROF) will be indicated by a solid GREEN LED.
The default Max ROF is 11 flashes (13 BPS).
Dwell Setting will be indicated by a solid ORANGE LED
The Dwell setting determines how long the Slip Stream(TM) Solenoid is
open. The Dwell is defaulted at setting 28 and is adjustable from 1 to 45.
Note: If the Dwell Setting is adjusted too high or low, the TM-7 will not
function correctly.
Ball in Place Delay (BIP) will be indicated by a flashing RED LED.
The BIP is defaulted at 10ms (each Flash = 1 millisecond). BIP is adjust-
able from 1 to 40 milliseconds.
Note: If you are not using a force-feed loader, it is recommended that
you use a higher BIP setting.
Flashes/ROF Flashes/ROF Flashes/ROF
1 Flash = 8 BPS
2 Flash = 8.5 BPS
3 Flash = 9 BPS
4 Flash = 9.5 BPS
5 Flash = 10 BPS
6 Flash = 10.5 BPS
7 Flash = 11 BPS
8 Flash = 11.5 BPS
9 Flash = 12 BPS
10 Flash = 12.5 BPS
11 Flash = 13 BPS
12 Flash = 13.5 BPS
13 Flash = 14 BPS
14 Flash = 14.5 BPS
15 Flash = 15 BPS
16 Flash = 15.5 BPS
17 Flash = 16 BPS
18 Flash = 16.5 BPS
19 Flash = 17 BPS
20 Flash = 17.5 BPS
21 Flash = 18 BPS
22 Flash = 18.5 BPS
23 Flash = 19 BPS
24 Flash = 19.5 BPS
25 Flash = 20 BPS