OWNER’S MANUAL W W W. E M P I R E B AT T L E T E S T E D .
CONTENTS 1. RULES FOR SAFE MARKER HANDLING 1 2. INTRODUCTION AND SPECIFICATIONS 1 3. GETTING STARTED 1 4. FIRING YOUR MARKER 3 5. VELOCITY ADJUSTMENT 3 6. ACCESSORY ADJUSTMENTS 3 7. UNLOADING YOUR MARKER 4 8. REMOVING AIR SUPPLY 4 9. CLEANING MARKER 4 10. STORAGE AND TRANSPORTATION 4 11. DISASSEMBLY / REASSEMBLY 4 12. PARTS LIST & DIAGRAMS 7 WARRANTY (Inside Back Cover) For manuals and warranty details, go to: paintballsolutions.
1. Rules for Safe Marker Handling IMPORTANT: Never carry your Marker uncased when not on a playing field. The non-playing public and law enforcement personnel may not be able to distinguish between a paintball marker and firearm. For your own safety and to protect the image of the sport, always carry your Marker in a suitable marker case or in the box in which it was shipped. • Treat every marker as if it were loaded. • Never look down the barrel of a paintball marker.
Safe Mode In this manual, you will see the term “SAFE” mode. The Power should be OFF (Fig. 3.1) on electronic grips, or the Safety should be set to “SAFE” (red marking on safety will not be visible) Fig. 3.2. Make sure your marker is set to “SAFE” mode when indicated to do so. Barrel Installation Safety OFF Fig. 3.1 Note: It might be necessary to adjust the clamping feed elbow screw to fit your loader.
Notes: • Remember compressed air, nitrogen systems and CO2 cylinders can be extremely dangerous if misused or improperly handled. Use only cylinders meeting D.O.T. or regionally defined specifications. • Never disassemble your tank or tank regulator. Only a qualified and trained technician should perform work on your tank and tank regulator. • Never add any lubricants or greases into the fill adapter on your tank regulator. Loading Paintballs Safety OFF Empire BT markers use .
7. Unloading Your Marker 1. Put on an eye protective device designed specifically for paintball and make sure that anyone within range of the Empire BT-4 Slice Marker does the same. 2. Make sure the barrel blocking device is properly installed and the marker is set to “safe” mode. 3. Loosen the loader clamping screw or release clamping arm. 4. While holding the paintball hopper in place, invert the marker so that the hopper is below the Empire BT-4 Slice marker. 5. Remove the loader and all paintballs.
Disassembly/Reassembly (continued) Note: It may not be necessary to loosen the 3 screws on the Delta rear sight; see if it slides off first. Disassembly Tips Trigger Frame Removal • Make sure you have a clean area to work on your marker. • When separating the Shell for the first time, do so carefully, so you do not lose any parts. • Visit PaintballSolutions.com for additional information. Barrel Removal Fig. 3.7 Turn the barrel counter clockwise to remove it from the marker.
Removing End Cap/Stock, Spring Guide, Bumper and Spring Fig. 4.4 1. Remove the Rear Trigger Frame pin as described previously in the Splitting the Body section 2. Split the upper shell from the lower, making sure the barrel plug stays seated to not interfere with the upper shell pivoting 3. Locate the pin that holds the End Plug in place (Fig. 4.4) Fig. 4.5 4. Push the pin out of the lower Body, making sure that you do not try to push the knurled end 5.
K Empire BT Feednecks Parts List 4 2 3 SCHEMATIC# DESCRIPTION................................................................................................................................SKU# 5 1 1 2 3 4 5 Clamping Feed Elbow Screw............................................................................................................................................17759 Clamping Feed Elbow Lever....................................................................................................
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 LONG RECEIVER BOLT BODY SHELL TOP LOGO LINKAGE ARM SUPPORT BARREL ADAPTER TOP FEED ELBOW DETENT DETENT SHELL SCREW SHCS 10-32 X 1.
Warranty Information LIMITED LIFETIME WARRANTY INFORMATION (ORIGINAL PURCHASE RECEIPT REQUIRED) Empire BT Paintball warrants that this product is free from defects in materials and workmanship for as long as it is owned by the original purchaser, subject to the terms and conditions set forth below. Empire BT Paintball will repair or replace with the same or equivalent model, without charge, any of its products that have failed in normal use because of a defect in material or workmanship.
10 E M P I R E B A T T L E T E S T E D .
EMPIRE BATTLE TESTED PAINTBALL 11723 Lime Kiln Rd., Neosho, MO 64850 www.empirepaintball.
