Page 1 of 8 MATERIAL SAFETY DATA SHEET Trisodium Phosphate Section 01 - Chemical And Product And Company Information Product Identifier ……………………... Trisodium phosphate Product Use …………………………..... Industrial chemical, textiles, water treatment Supplier Name……………………….…. ClearTech Industries Inc. 2302 Hanselman Avenue Saskatoon, SK. Canada S7L 5Z3 Prepared By................……………..….. ClearTech Industries Inc. Technical Department Phone: (306)664-2522 Preparation Date.........…………….…...
Page 2 of 8 Skin Contact / Absorption…….…... May cause moderate skin burns. May cause severe irritation, especially if skin is moist or wet. Eye Contact................………….….... May cause eye burns. May cause permanent corneal injury. May cause severe eye irritation. Ingestion.....................………………. May cause burns of the mouth, throat and stomach. Aspiration in to the lungs may occur during ingestion or vomiting, resulting in lung injury. Exposure Limits……………………...
Page 3 of 8 Additional Information.....…………... Treat symptomatically. Ingestion of large quantities of phosphate salts (over 1.0 grams for an adult) may cause an osmotic catharsis resulting in diarrhea and probable abdominal cramps. Larger doses such as 4-8 grams will almost certainly cause these effects in everyone. In healthy individuals most of the ingested salt will be excreted in the feces with the diarrhea and, thus, not cause any systemic toxicity.
Page 4 of 8 Section 06 - Accidental Release Measures Leak / Spill................….……………... Wear appropriate personal protective equipment. Scoop up or vacuum spilled material and place in appropriate closed container. Flush area with water to remove any trace residue. Prevent material from entering sewers. Deactivating Materials...……….…... Not available Section 07 - Handling and Storage Handling Procedures.......…………... Avoid contact with eyes, skin and clothing. Avoid breathing in dust.
Page 5 of 8 Ventilation Requirements………...... Mechanical ventilation (dilution or local exhaust), process or personnel enclosure and control of process conditions should be provided. Supply sufficient replacement air to make up for air removed by exhaust systems. Other………………………………….... Emergency shower and eyewash should be in close proximity. Section 09 - Physical and Chemical Properties Physical State.......……....………….... Solid Odor and Appearance…..…………...
Page 6 of 8 Hazardous Products of Decomposition.. Oxides of phosphorus and sodium Polymerization...........…………….…….…. Will not occur Section 11 - Toxicological Information Irritancy.................……..………….…. Irritating to skin & respiratory area, extremely irritating to eyes. Sensitization........…….......………….. Not available Chronic/Acute Effects……...……….. Inhalation of product may aggravate existing chronic respiratory problems such as asthma, emphysema or bronchitis.
Page 7 of 8 Section 14 - Transportation Information TDG Classification Class……………..………………..….... 9 Group...............…………….......……... III PIN Number.................……..……….... UN3077 Other…………………………………..... Secure containers (full and/or empty) with suitable hold down devises during shipment. Section 15 - Regulatory Information WHMIS Classification.......…………....
Page 8 of 8 ClearTech Industries Inc. - Locations Corporate Head Office: 2302 Hanselman Avenue, Saskatoon, SK, S7L 5Z3 Phone: 306-664-2522 Fax: 306-665-6216 www.ClearTech.ca Location Richmond, B.C. Calgary, AB. Edmonton, AB. Saskatoon, SK. Regina, SK. Winnipeg, MB. Mississauga, ON. Address 12431 Horseshoe Way 5516E - 40th St. S.E.
MATERIAL SAFETY DATA SHEET FOR COATINGS, RESINS, AND RELATED MATERIALS DATE OF PREPARATION - 01-03-2009 Prepared by: Compliance Dept. SECTION IV - FIRE AND EXPLOSION HAZARD DATA DANGER! – FLAMMABLE VAPORS MAY CAUSE FLASH FIRE Sensitivity to Static Discharge - Grounding/Bonding required Extinguishing Media - Dry Chemical, Foam or CO2 Flash Point 27 C or 80 F TCC LEL 0.9% Autoignition Temperature 379 C/715 F UEL 8.
Product ingredients appear on the following carcinogenic listings: (X) IARC (X) NTP ( ) OSHA ( ) None of the above. PRIMARY ROUTE(S) OF ENTRY (X) SKIN (X) BREATHING PERSONAL PROTECTIVE EQUIPMENT – Do not get in eyes, on skin, or on clothing. Use solvent resistant safety eyewear with splash guards. Solvent impermeable gloves, clothing, and boots should be worn to prevent skin contact.
MATERIAL SAFETY DATA SHEET FOR COATINGS, RESINS, AND RELATED MATERIALS DATE OF PREPARATION - 01-03-2009 Prepared by: Compliance Dept.
dermatitis which may include rash, itching, hives and swelling of extremities. In those who have developed a skin sensitization these symptoms can develop as a result of contact with very small amounts of liquid material or even as a result of vapor-only exposure. – High vapors may result in central nervous system depression. – Hemorrhages into various vital organs have been noted. – Coma may result from overexposure.
MATERIAL SAFETY DATA SHEET FOR COATINGS, RESINS, AND RELATED MATERIALS DATE OF PREPARATION - 01-03-2009 Prepared by: Compliance Dept.
RESPIRATORY PROTECTION: Use approved chemical/mechanical filters designed to remove a combination of particulates and organic vapor in open and restricted ventilation areas. Use approved airline type respirators or hoods in confined area. PROTECTIVE GLOVES: Use neoprene or rubber gloves to prevent skin contact. OTHER PROTECTIVE EQUIPMENT: Use protective cream if skin contact is likely. Use disposable or impervious clothing if work clothing contaminations likely.
MATERIAL SAFETY DATA SHEET FOR COATINGS, RESINS, AND RELATED MATERIALS DATE OF PREPARATION - 01-03-2009 Prepared by: Compliance Dept.
