Service manual

IMPORTANT SAFETY AND WARNING INFORMATION
!
This product is a variable height, adjustable
mattress platform, which will provide comfort and
convenience for residents/patients and caregivers in
long term care settings.
!
The MAXIMUM SAFE WORKING LOAD for the
Zenith 7000 Bed with weight evenly distributed,
including bedding, resident/patient, support surface,
and all accessories, is 500 lb.
!
NEVER operate the bed if a Power Cord or Plug is
damaged or not working properly. Contact qualied
Service Personnel for examination and repair.
Always unplug the Power Cord before performing
maintenance on the bed.
!
DO NOT open assemblies such as the Actuators,
Hand Control Pendant, or Control Box. If
unauthorized personnel perform work on these
components, the manufacturer’s warranty becomes
void.
!
DO NOT use unauthorized parts, accessories, or
adaptors other than those specied/authorized by GF
Health Products, Inc.
!
When operating the HI/LO, Knee, or Back Functions
of the bed, ALWAYS ensure the conned individual
is positioned properly within the connes of the
bed. DO NOT let any extremities protrude over the
side or between the bed rails when performing these
functions.
!
DO NOT lower the bed when objects are beneath it.
Failure to inspect under the bed can result in personal
injury or property damage.
!
The bed’s Hand Control Pendant Cable MUST BE
ROUTED AND SECURED PROPERLY to ensure
it does not become entangled and eventually severed
during use. Also ensure electrical cords DO NOT
get tangled around the bed, side rails, or legs during
transport or normal operation of the bed.
!
When using nasal-type or masked-type administering
equipment, all oxygen or air tubing MUST BE
ROUTED AND SECURED PROPERLY to ensure
that the tubing does not become entangled and
eventually severed during the normal operation of the
bed.
!
Keep all moving parts free of obstructions (i.e.
blankets/sheets, heating blankets/pads, wiring, etc.).
!
Beds manufactured by Basic American Medical
Products are designed for use within an institutional
healthcare environment (i.e. assisted living, skilled
nursing, transitional care, rehabilitation care, etc.).
!
DO NOT use the assist devices as push handles for
moving the bed. Assist devices can be deformed or
broken if excessive side pressure is exerted. Assist
devices are not meant for patients considered high
risks for entrapment (i.e. patients with pre-existing
conditions such as confusion, restlessness, lack of
muscle control, altered mental status, either organic
or medicinal, or a combination thereof). Additional
safety measures should be considered for such high-
risk patients.
!
NEVER permit more than one person on/in the bed at
any time.
!
Body weight should be evenly distributed over the
sleeping surface of the bed. DO NOT allow the
patient to lie, sit, or lean in such a way that their
entire body weight is placed only on the raised head
or foot section of the bed. This especially applies
when repositioning or transferring a patient in or
out of the bed. Increased risk may occur when the
patient’s size and/or weight are inappropriate for the
bed’s dimensions or weight capacity.
!
Risk of entanglement or injury may occur if the
mattress used with mattress retainers does not ll the
entire width between stops or which compresses to
less than 1.50 inches under user’s weight.
!
Mattress must be properly sized to t the mattress
support platform and must remain centered on
the support platform relative to State and Federal
guidelines. Recommended minimum dimensions
of mattress are 35 inches wide and 6 inches deep.
Length should match the mattress support platform.
Use of an improperly tted mattress could result in
injury or death.
!
IMPORTANT: Powered air mattress surfaces may
pose a risk of entrapment. Prior to use, ensure the
therapeutic benets outweigh the risk of entrapment.
!
The bed is intended for use, storage, and transport
within a temperature range of -40˚C to 60˚C. It has
a water resistance rating of IPX4 and IS NOT to be
power washed or submerged.
GF Health Products, Inc. - www.grahameld.com Zenith 7000 Service Manual 999-0843-190E
ZENITH SERIES
4