Instructions

ManualsBrandsBasetech ManualsCar & BicycleBasetech Antifreeze and Coolant Tester

Overview

1 Pump

2 Small arrow

3 Body

4 Large arrow

5 Freezing point scale

6 Hose

7 Boiling point scale (on rear)

Using the Tester

The tester should be clean before starting the testing procedure. Pump and ush

clean warm water through the tester if needed.

Risk of burns! Make sure vehicle engine is cool before testing.

• Remove the radiator or expansion tank cap.

• Insert the tester hose (6) and squeeze the pump (1) to draw uid into the tester.

Fill to the FLUID LEVEL line.

• Line the tester up so the small arrow (2) is lined up vertically between the

crosshairs as shown.

• Tap the tester body (3) to remove any air bubbles.

• The large arrow (4) indicates the freeze point (5) / boiling point (7).

• Return the uid to radiator by squeezing the pump, then rinse the inside of the tester out by

ushing with clean warm water.

- If needed, replace or add additional antifreeze/coolant.

- The readings may not be accurate if the antifreeze/coolant is dirty or contains rust. If

needed, ush and rell the cooling system then test again.

Care and Cleaning

• Pump then ush clean warm water through the tester before and after each use.

• Do not use aggressive cleaning agents as they can cause damage to the housing and

malfunctioning.

• Clean the product with a dry, bre-free cloth.

Technical Data

Supported uid type ...................... Ethylene glycol

Tester material .............................. Pump: Rubber

Body: PS (Polystyrene)

Tube: PVC

Measuring range ........................... Freeze point: -12 °C to +43 °C

Boiling point: 125 °C to +131 °C

Units of measure .......................... °C / °F

Dimensions ................................... Antifreeze Tester: 72 x 187 x 51 mm (W x H x D)

Dimensions ................................... Pump: 51 x 67 mm (Ø x H)

Body: 72 x 104 x 19 mm (W x H x D)

Tube: 10 x 156 mm (Ø x H)

Weight .......................................... 95 g

LEVEL

FLUID

Operating Instructions

Antifreeze and Coolant Tester

Item No. 2108037

Intended Use

This product is used to test vehicle antifreeze/coolant to avoid winter freezing and summer

overheating. It works with all ethylene glycol mixtures, indicating the freezing and boiling points

of your mixture. A clear container allows you to inspect the uid for rust, sludge, or other debris.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged. In

addition, improper use can result in other hazards. Read the instructions carefully and store

them in a safe place. Make this product available to third parties only together with its operating

instructions.

This product complies with the statutory national and European requirements. All company

Delivery Content

• Tester • Operating instructions

Up-to-date Operating Instructions

Download the latest operating instructions at www.conrad.com/downloads or

scan the QR code shown. Follow the instructions on the website.

Explanation of Symbols

The symbol with the exclamation mark in the triangle is used to indicate important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on operation.

Safety Instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information

on proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the appliance from strong jolts and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• The use of safety glasses and protective gloves are recommended when removing

the radiator cap.

Avoid contact with skin. Wash with soap and water in case of skin contact. Do not

swallow. Contact a doctor immediately if swallowed.

• Risk of burns! The radiator cap should never be removed when the car is running

or the engine is warm. The liquid in the radiator can become extremely hot and

cause harm.

• Refer to your vehicle operating instructions and consider your location to

determine the best antifreeze/coolant to water ratio for your vehicle.

• Consult an expert when in doubt about the operation or safety of the tester.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights

including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication

represent the technical status at the time of printing.