Instructions

b) Batteries
• Correct polarity must be observed while inserting the battery.
• The batteries should be removed from the product if it is not used for a long period
of time to avoid damage through leaking. Leaking or damaged batteries might
cause acid burns when in contact with skin, therefore use suitable protective
gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying
around, as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and new batteries in
the product can lead to battery leakage and product damage.
• Batteries must not be dismantled, short-circuited or thrown into re. Never
recharge non-rechargeable batteries. There is a risk of explosion!
Operating Elements
10
11
12
13
14
1
2
3
4
5
6
7
8
9
Doorbell Chime
1 5 V/DC 1A power input
2 Wall hang
3 Loudspeaker
4 LED status indicator
5 Battery compartment
Bell Push
6 Top wall mount hole
7 Bell push button
8 Bottom wall mount hole
9 Cover release tab
Bell Push (Internal View)
Image is for reference only.
10 LED status indicator
11 PLAY button
12 SELECT button
13 Battery release tab
14 Battery slot
Installation
Check that the supplied screws are appropriate for the surface material. If in doubt
consult a professional.
Before drilling, check for concealed wires or pipes beneath the surface that could be
damaged or cause harm.
It is recommended to test the operation by placing the devices in the approximate
locations of use before nal installation.
a) Bell Push
The bell push can be attached to a surface using adhesive tape or mounted using screws and
dowels.
Adhesive Tape
• Before adhering, the surface should be clean, dry, smooth and residue-free.
• First remove one side of the tape and apply it to to back of the bell push.
• Remove the other side then attach the bell push to the wall.
Wall Mount
• Use the cover release tab (9) to lever off the bell push housing.
• Secure the back of the housing with two screws and dowels (if needed) to the desired
surface. Be careful not to damage the circuit board when you do this!
• Before replacing the housing, insert the CR2032 battery then select one of the 30 audio
signals if needed.
See sections “Inserting Batteries” and “Choosing a Doorbell Chime” for further
information.
b) Doorbell Chime
• The doorbell chime can be hung to a wall from the wall hang (2).
• Use an included screw and dowel (if needed).
Operating Instructions
Radio Controlled Doorbell Chime
Item No. 1890360
Intended Use
These devices are intended to be used together as a wireless bell push and doorbell chime.
Choose between 30 different pre-programmed audio sounds for the doorbell chime.
The doorbell chime (receiver) is intended for indoor use only. Do not use it outdoors. Contact
with moisture, e.g. in bathrooms, must be avoided under all circumstances.
The wireless bell push (transmitter) has an ingress protection rating or IP44. It can resist a light
splash of water to the front casing when wall mounted. It should be used in covered outdoor
areas.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, res, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Doorbell chime (receiver)
• Bell push (transmitter)
• 3 V CR2032 battery (pre-installed in
remote)
• Double sided adhesive tape
• 3x Screw
• 3x Dowel
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General Information
• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about the operation, safety or connection of the
product.
• Maintenance, modications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.